1108875279A Kenmore Washer Dryer Combo - Instructions

First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great

pop the cap off the top of center agitator unit, remove one 11mm bolt and remove unit from washer. take apart, remove & replace broken dogs and reassemble. I actually bought the wrong kit, my cam is much longer but since the problem was caused by the broken dogs it did not matter.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

replace basket with new one snapped in

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

my hany man did it....

It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.

Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.

I called a repairman, who diagnosed the problem as a faulty leaf switch in the lid assembly -- the little rod on the lid that normally would depress the switch was working fine, but the switch was not closing. At my direction, he bridged the wires from the switch as a test, and it worked fine. So I ordered a new switch from you guys and swapped the new one out with the old one. Two flat screws to remove the slanted top panel, and at the rear of the panel are two hex-top screws holding the lid assembly on. Undo the hex-top screws, lift off the lid assembly, unplug the interlock between the washing machine power and the lid, and find a clean place to lay the lid assembly. Replacing the switch is a snap -- the part you sold came with its own wiring, and all it takes is take the old part out and put the new part in. Easy peasy. Getting the lid assembly back takes a little work because the fasteners are a little tricky to position correctly -- they will fall off the lid assembly and repositioning them may involve a bit of trial and error -- but once it is properly positioned, it takes a total of six screws and you're done. Two for the switch (Philips), two hex heads to fasten the lid assembly to the washer chassis, two to button up the front access panel.. A caution -- make sure the machine is unplugged when you do the repair, or else the washing machine may cycle into a spin cycle when you plug the interface back in and surprise you.

I misdiagnosed the problem as heater element because I did not have my voltage meter with me. The problem was the heat thermostat that senses temperature in the drum and burns out if it's too high. There are two other safety cut off thermostats that when triggered will reset themselves when the temp cools. All three should be tested before looking for something else, like the cycle selector switch; that one is not only more complex but very difficult to access. One is on the heater element itself, the other senses the temperature of air flowing out of the heater element. I believe this array of thermostats is similar on every drier. Each one should be tested with an electrical multifunction tester before guessing what's wrong. The drum thermostat, a $13 part, was the easiest to replace, once I got the back of the drier completely open, a not too difficult task. And, as I found out talking to a repairman, is the thermostat that most commonly fails. I will add that Partselect was most accommodating in providing advice and in authorizing me to return the heater element and refunding the overnight shipping fee. And their web site is terrific--the only drawback being you have to read it over thoroughly before concluding you are an "expert". I would work with them before any other vendors. Good luck!

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

Watch the video before I received the part. Made it very simple to replace and which screws to take out.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!