11081432510 Kenmore Washer Dryer Combo - Instructions

Followed by installation on line

unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged electric and put drain hose back to drain done

This should have been done under 30 minutes but when you don't have a repair manual, you have to do some guessing. I have to remove the back panel. On only thing that was hard was unspringing the two flat springs. After I got the panel off, the rest was easy and the dripping stopped. Oh, there is a screen where the hose connects to the inlet valve. If you can clean the screen often, you can continue to get a good water flow.

I just followed the instructions found on this website. It covered everything you need to know. I have just one thing to add though. Look over everything first and formulate a game plan. Keep all screws etc. and put them in a plastic bag so you don't lose them. You might try using a heavy hammer to force the clips holding the back panel to the top of the machine back in place. One more thing; use a piece of wood to set the back panel on while you replace the intake valve.

unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clamp #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.

The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.

The hot water hose was frozen to the hot water bibb and it took me a while to cut it loose with my Dremel tool. Removed the cabinet and replaced the water inlet valve easily, then hooked up new hot and cold water hoses. Reinstalling the cabinet was a little tricky getting it lined up correctly. Checked for leaks then tested the washing machine and it ran great with the water filling the machine much faster with the new Water Inlet Valve. I will definitely replace the washing machine hot and cold water hoses every 5 years from now on.

The repair went great. The video shown on the partselect site saved me a huge amount of time disassembling the cabinet to access the malfunctioning part. The most difficult part of the repair was replacing the cabinet on the unit after the part swap and getting it straight. Luckily 2 attempts was enough. I recommend trying this repair yourself and saving a bunch of $$.

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

I followed the instructions I found on your website. It made it very easy. Easier than if I had tried to do it the way I thought I had to remove the back of the washer. Going through the top panel made removing the bottom panel screws unnecessary.
The experts were correct, the instructions precise. Thank you

Removed top control panel, removed inlet mount hardware, removed both electrical connectors, removed filler hose, Installed new inlet valve in reverse order. Works fine !

I followed the video instructions to the tee. Took more time to move the machine out and put back than to replace the inlet valve.

My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.

I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.