11081432510 Kenmore Washer Dryer Combo - Instructions

just replaced parys

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

first of all, the parts i ordered arrived THE NEXT DAY, which is fantastic. and all for under a hundred bucks. secondly, the parts came with excellently detailed instructions that included photos, so the repair itself was pretty easy. i opened up the washer, disconnected 2 hoses, slid the entire tub/motor assembly out as directed, loosened the nuts holding the old suspension springs in place, removed the old tub spring, lifted the tub off the old suspension springs, removed and replaced the springs with new ones, and put everything back together again. tub is tight, spin cycle is nearly silent...it's like a new machine. the only reason the repair took as long as it did was because i took the opportunity to clean everything out in there--about a decade worth of grime and dust. cleaned the hoses, cleaned up the tub, cleaned under everything. this is my second repair with partselect (the dryer half of my machine went bad last month), and the second time the repair has gone flawlessly. i couldn't be happier.

Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.

I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.

This should have been done under 30 minutes but when you don't have a repair manual, you have to do some guessing. I have to remove the back panel. On only thing that was hard was unspringing the two flat springs. After I got the panel off, the rest was easy and the dripping stopped. Oh, there is a screen where the hose connects to the inlet valve. If you can clean the screen often, you can continue to get a good water flow.

unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clamp #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.

After reading everyone elses stories, I purchased all new springs(5), new spring brackets(one of mine was rusted really badly)and all new wear pads(two sets of 3pcs each). The rusted spring bracket was the most time consuming as the screw was rusted into the bracked so I had to drill it out. Other than that, the actual spring replacement was easy. Took maybe 10 minutes. The wear pads were another story. I'm a pretty good mechanic and I had a bit of a struggle getting the old pads out. I used a long, flat head screwdriver to pry them out. Once they were out the new ones weren't too tough to get back in. Took about 20 minutes all together. I stongly recommend watching the video on removing the washer cabinet first. It will save you some time. Acutally, watch the videos on all of the parts to simplify the process. Oh and by the way, all of my washer problems are gone. Well worth my time and $70 in parts. Good web site!

the tube when spinning the tub would shake so bad the washer would walk away from the wall but it will not happen anymore since I put the new spring on it runs great and this is not my first rodeo. Removed the outer part to timer controls then removed two screws then shell in front came off the body

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged electric and put drain hose back to drain done

The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.

I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple

received valve as ordered a simple installation. everything went well.home owner can do this repair

slipped new rear leveling legs into leveling fixture. Fit even though it wasn't specified to be the right part for this old washer.