11060222510 Kenmore Dryer - Instructions

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Opening the dryer to discover the problem was easy. We put the belt up on a workmate bench - I think this made access better at the bottom. Getting the new belt on past the rear drum seal was ok, the instructions could benefit by including wording describing how to roll the belt flat under the 2 rear drum support pulleys to bring it to the drive motor shaft pulley. The instructions included with the belt had a diagram showing the position of the belt take up idler (the idler was found loose inside the bottom of the dryer), our dryer had a hole in the metal spring clip of the idler arm, so we thought at first that a screw to the chassis had broken - this is not the case the idler pulley is held in place by belt tension, so pulling the spring clip open while feeding the belt would have been useful in the instructions too. Other than those 2 head scratchers the repair was easy and saved us the cost of calling a repairman. Thanks PartSelect.

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

I went to repair the dryer belt only to realize that it was jumping off the pulley(edge was worn away). If you are replacing the belt, make sure your pulley is good before you order your parts. I ended up having to go to lowes and make a pulley!
Works great though.

Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

replaced rollers, belt and pulley. Video was very helpful

flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.

Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.

I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!

Made a BIG mistake ordered replacement part based on Model number of dryer. The part I received was wrong. Took out the broken part and found a part number on it. Reordered a new part based on that number. When it arrived, replacement took about 15 minutes. Lesson learned: see if number on part to be replaced. Don't trust the Model number.