11021182013 Kenmore Washer - Instructions

1st watched the video, turned off the water supply, unplugged the elecrtcal cord, removed the rear top panel , screws with the nut driver , then slid the top forward about 1 inch & then lifted upwards to removed the lid assy, after taping the lid assy down so it wouldn't flip open. Then once lifted up, at the very back are 2 slots, which you can the set the top onto, then use the 2 s-hooks with a chain to support the lid assy from falling backwards and attach to the base assy.
Then you can move the tub assy away from where you need to work.in this case was replacing the upper plastic suspension rod supports, then push upwards the socket , drop in the new one, pull of on the rod assy, and hook it into the ball and drop bach into the suppprt , was able to do all 4 in no time. Then unkook and reattach all, screws, plug back in, turn on the water. And we were good to go.
All For less than $20.

online videos were great. called to order and lady was very helpful. washer is now operating normal

Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting noise. Reassemble. The drawing on this site is helpful.

followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.

chage out part and washer still shake

Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.

Unplugged remove hoses remove drain hose turned over on its back remove suspension Springs installed new Springs good backup connected Springs did not solve problem

Pop the cap on the agitator with a screwdriver then take out the bolt underneath. Replace the agitator dogs.

When putting the bolt back, don't tighten like its going to jump out of the washer. I think that's why I had to replace it a second time

I found the Agitator "dogs" (really that's their name) to be stripped. Ordered the part and got it within two days. It was a very easy fix and the old washer works great now.

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Cogs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .

I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .