11020102310 Kenmore Washer - Instructions

Followed instructions.

undo one bolt and change agitator kit

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

Ordered the inlet assembly from this site. Received it the day after I received the notice it shipped. Watched their video of how to replace the part. Easy job, done in 15 minutes. Only needed a screwdriver to take the cover off the back of the washer control panel. A company wanted $400 to replace the part.
Definitely recommend the company and will use again.

My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.

used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut driver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.

I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!