10650022210 Kenmore Refrigerator - Instructions

Followed the video instructions.

Order new shelves

I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.

pulled the control panel removed 2 screws holding the board unpluggedwiring harneses plugged in new board mounted it plugged in the fridge and set the thermostats it came on and temps holding for 5 days so far, very pleased with ease of repair and results, very easy.

Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.

Remove the 2 bolts in the front. Remove water pump from back so you can easily remove hose coming from filter housing. Remove screw holding inlet water hose so it's free to move. Pull filter housing out the front and disconnect water lines. Attach new filter to water lines and when pushing filter housing back into place you have to hold Styrofoam support with other hand or it will fall over. Reconnect in reverse order.

Just as shown on your video.The refrigerator side was not sitting even, clunked and did not seal right. I decided to do.both sides, refrigerator and freezer while I was at it as our refrigerator is about 16 years old. Everything went in easily and saved us a lot of money. Very happy with the parts and repair video. Got the refrigerator nice and cleaned out while we were at it..Us and the refrigerator are breathing easier now..Yeepppeee....

Open door and from appliance instruction book
Replace filter

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into the slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

The hard part was getting the right part ordered!
The exploded view needs to be bigger as it is hard to differentiate.
A phone call fixed everything.

After viewing online videos of the repair process, it was very easy to replace the evaporator fan motor - just remove the back panel of the freezer compartment for EASY access to the evaporator motor. I received the new motor a day earlier than I thought I would. I took 15 to 20 minutes to replace the old motor. The only problem was the wiring on the new motor was on the opposite side of the motor as compared with the old motor. I was able to rotate the new motor enough for the new wiring to connect. VERY HAPPY with the results. A word of caution: the motor mounting brackets are plastic - go easy when trying to remove the brackets.

Simply cut the water tube on both sides of connector and push in the new one.