106482394 Kenmore Ice Maker - Instructions

three screws and a plug in and it was done!

The icemaker was an exact duplicate of the one in my refrigerator. I installed the correct shutoff bar on the icemaker and removed the tab for the water fill spout. After pulling the power cord I loosened the two top screws with a nutdriver and removed the bottom screw. I pulled the icemaker from the rear wall, away from the fill spout, and disconnected the wire harness. Installation was just the reverse of the removal.

I removed one screw from lower portion of unit and loosened 2 top screws. Lifted unit to slide off top screws and unplugged unit. Plugged in unit and positioned unit on 2 top screws. Installed bottom screw and tightened top 2 screws. Repair complete.

added lowering clips to brackets, plugged it in,
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.

I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.

replaced the element as described. it worked for 2 cycles and flooded the capture tray. I thought it may be an issue with the water supply line so I replace it and insured it was getting a good feed.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.

Removed old ice maker and replaced it with the new one, took 20minutes and existing plug worked so I didnt have to use an adapter. Been 36 hours and it makes ice fine but has only dumped 3 or 4 times, hope it gets better. I dont know what else to do to it. Proceedure was easy and quick./

I looked up the model# of my kenmore for repairs and partselect.com came up. I searched for the icemaker, wondering if I was even going to be able to figure it out. I was pleasantly surprise that when I found the part there was also a video on how to do the repair. I watched the video, ordered the part and when it came, the repair was a piece of cake.

Parts arrived amazingly fast. Replaced top ice maker and bottom water control valve[which was probably the source of my problem all along] in about an hour. The online installation video's were a big help. Thanks.

My husband removed the old ice maker and had the new one put in, in about 30 minutes very easy fix we have bought washing machine parts from part select in the past it was an easy fix too this is a great company good prices and quick delivery it saved us a bunch of money it pays to fix stuff instead of getting a new appliance

removed 3 screws as per instruction, no problem getting olf one out; putting new one in was a big problem, I finally ended up taking the door off ice storage bin, this gave me an extra 1/2 inch up room to go up, I also used 1.0 inch screws, the 1/2 ones that came with . were too short, I put the screw in 1/4 inch I manuvered the ice maker over the two top screws tightened, and than put the 1/2 screw in the bottom attach hole . the longer screws&removing the door made it easy. van nolf

Replaced ice maker with new one but found it was not the ice maker at all. There was an accumulation of ice in the duct inhibiting the flow of cld air to the ice maker. I cleared the ic build up in the duct and it has been working just fine. But am concerned about make up water leaking into the duct.

replaced ice maker works great thanks

I removed the old ice maker wich was easy and just reinstalled the new one. If you are a little knolageable and watch what you are doing it is very easy to install.

Troubleshot to the icemaker as per the troubleshooting guide that came with the refrigerator. Could not initiate a harvest cycle by jumping the appropriate test ports on the drive side of the ice maker. Verified the proper voltage was present with a DVM. Ordered new ice maker, really easy on-line with PartSelect interface. Installed new unit in about 5 minutes and the unit dropped the first batch of ice about 2 hours later. Works great!