106482394 Kenmore Ice Maker - Instructions

remove the ice bucket support bracket and remove bottom screw from icemaker, loosing the two top screws and slide icemaker back enoughto unplug electric harness

Removal was easy...Removing and installing arm was a bit difficult...Called a service man to install...He also had a bit of difficulty, but had it done in less than 45 minutes... He mentioned that my brackets had a different set up than most...

I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.

Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.

I took out the bottom locking screw and loosened the top two screws. I took the old icemaker out. I disconnected the wiring harness at the ice maker. I attached the new icemaker and mounted it in place. I didn't have to use any of the included wiring harnesses since the old one worked fine. I did use the old wire bale. I'm fairly ungifted in fixing things so I was amazed at how easy and inexpensive this was. The icemaker started up right away. The whole thing probably cost less that just the service call minimum would have been.

I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice maker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.

Removed three screws and unpluged wiring. Replaced new unit by plugging in wire and replacing three screws.

Lossen two screws at the top and remove one at the bottom and lift the unit off of the top screws, unplug the old unit and after cutting out the tray for the water fill spout plug the new one in. No problem .................

followed instructions and replaced unit.
very easy and will roder again from this

Tested water valve by disconnecting power and adding 110VAC to valve to be certain the valve worked before ordering new ice maker. Rather than guessing on the part of the ice maker that was defective I ordered a new ice maker complete for a few doorars more and that fixed the problem.

Turned off power and water, removed 2 screws on the bottom, loosened 2 screws on the top, pulled ice maker out a couple inches so I could disconnect wires, and removed old ice maker. I cut the slot in the back of new ice maker for the water line with pocket knife and installed the new unit. Took less the 30 minutes.

After turning off the water to the fridge, I removed the 3 screws holding the icemaker, and unhooked the wire harness. I just reversed the process to reinstall and it took about 20 minutes, and we had a bin full of ice the next day.

I first removed the door, very easy to do, then removed one screw that held the icemaker in place. I then unplugged the electricity to the frig, slid the unit out and disconnected the electrical harness. Luckily the harness on the new icemaker matched up with the original plugin on the frig so it wasn't necessary to change the wiring on the new part. I simply slid the new icemaker in plugged it in put the retaining screw in, the door on, plugged the frig in and started makinmg ice. Couldn't have been easier.

I removed the 3 screws that held the unit in place and disconnected the power supply from the front part of the icemaker. I then assembled the replacement icemaker and plugged it in to power supply. I then mounted it with the 3 screws that it required. (Tip): Note the top 2 screws do not need to be totally removed just loosen them enough to remove icemaker. I then cycled the iemaker shutoff arm several times and within 45 minutes I had my first ice cubes

replaced the element as described. it worked for 2 cycles and flooded the capture tray. I thought it may be an issue with the water supply line so I replace it and insured it was getting a good feed.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.