All Installation Instructions for Kenmore Refrigerator 10641153210

Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

Parts Used:

Refrigerator Bimetal Defrost Thermostat

George from ENDWELL, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Leaky door gasket

Looked up on you tube to verify and see "secrets" to installation.

Parts Used:

Fresh Food Door Gasket

Freezer Door Gasket - White

Knick from DALLAS, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Parts Used:

Refrigerator Door Switch

David from Hemet, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

defective light switch

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Parts Used:

Refrigerator Door Switch

THOMAS from WILLARD, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Shelf was broken on one side.

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

Parts Used:

Door Shelf

Tammy from SHERMAN, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Freezer light out

Small flat head screw driver.Light is basically a computer module with plug connector

Parts Used:

LED Light

Damien from MILTON, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

changed the light bulb still would not work so I figured it was the switch sure enough.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Parts Used:

Refrigerator Door Switch

anthony from HAVELOCK, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Upper edge of plastic drawer broke off.

Slid the old drawer out and slid the new drawer in. Less then a minute!

Parts Used:

Refrigerator Crisper Drawer with Humidity Control

Harold from THE VILLAGES, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Crisper shelf glass missing

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

Parts Used:

Refrigerator Shelf Glass

Robert from SAUGERTIES, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

LED light blinking and going out in fridge

Installed new led light plug and play

Parts Used:

LED Light

Dwight from OLIVE BRANCH, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Light didnt go on

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Parts Used:

Refrigerator Door Switch

dorotea from staten island, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

THE SLIDE OUT SHELF WITH GLASS FRAMES WERE BROKEN.

I HAD TO BE CAREFUL...THE SHELF COST ME OVER $200/
iT WAS PACKED SAFELY AND THE GLASS SHELF ARRIVED SAFELY.
REMOVING IT FROM THE PACKING IS NOT TOO DIFFICULT...THE SHELF IS BROAD..

ONCE I WAS ABLE TO BRING IT OUT, I WAS ABLE TO REPLACE IT INTO THE REFRIGERATOR BY SLIDING IT INTO THE FRAME.

I AM NOT A HANDYMAN...BUT THIS WAS EASY.

Parts Used: