Whirlpool 80040 - Agitator Directional Cogs | PartSelect.ca
Agitator Directional Cogs – Part Number: 80040
Agitator Directional Cogs – Part Number: 80040 Agitator Directional Cogs – Part Number: 80040 Agitator Directional Cogs – Part Number: 80040 https://partselectca.azureedge.net/Schematics/Whirlpool/MDKTWLBF.gif

Agitator Directional Cogs

33 Reviews

Your Price

CAD$4.20

PartSelect Number PS388034
Manufacturer Part Number 80040
Manufactured by Whirlpool

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Estate, Inglis, Crosley, Maytag.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms: Will not agitate | Noisy | Pumps but will not spin | Spins slowly

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part Photo
Description
Price
Availability
(15)
PartSelect: PS334650
The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust spacer, inner cap seal, and washer. You ma...
$35.14
In Stock
PartSelect: PS334562
This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of a...
$5.15
In Stock
(3)
PartSelect: PS11741866
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$6.23
In Stock
Questions & Answers
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Installation Instructions Provided by PartSelect customers like you.
Average Repair Rating: 4.2 / 5.0, 265 reviews
What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
mike from Kent, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
80040
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
749 of 788 people found this instruction helpful.
Was this instruction helpful to you?
Craig from Polk City, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
80040, WP3363661, 285587
Washer not agitating
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assembly together it is a 7/16 head and because it is in a 4" deep well your will need a 6" extension for your ratchet. Once the bolt is out the top of the agitator, the assembly with the cogs removes by hand. Set the assembly upside down on the counter, slide the black plastic ring off, pull the cogs out with your fingertips, install the new cogs put a new black ring on and set the assembly back in the agitator. Reinstall bolt. As the bolt is down in a tube, you cannot set it in place with your fingers and it will fall out of the socket. To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket. Took me less then 10 minutes, good luck
576 of 595 people found this instruction helpful.
Was this instruction helpful to you?
dennis from new stanton, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
80040
top half of agitator did not move during wash cycle
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble
228 of 256 people found this instruction helpful.
Was this instruction helpful to you?
Greg from Hemet, CA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
80040, WP3349985, 285352
Gearcase oil leak
To replace gearcase seals, first disconnect the power cord. Turn off water supply and remove water inlet hoses at washer (safety first). You may want to have a bucket available to catch water that will drain out of the hot/cold and drain hoses. Next, remove top agitator cap, seal and (7/16”) bolt (see diagrams on PartSelect). This will allow the top agitator and cogs to be removed. Grab the bottom agitator and rock it back and forth until it can be removed.
Suggestion: now is a good time to remove and clean the old soap and junk from drain holes in the top agitator and any junk that may be under the lower agitator.
Lay the washer on its right side. You will now have access to the motor, pump, hoses clutch and gearcase. Place a couple of 2X4X(5?) blocks under the tub to support it. Remove the electrical connector from the motor (this is clipped into place) and the two wires that go to the capacitor on the motor.(TIP: don’t put your finger across these terminals, SHOCK HAZARD) Remove the hose clamps and hoses, the two screws (5/16”) on each strap that holds the motor in place, you may have to use a screw driver to pop the straps off the motor. Remove the motor and pump by pushing the tub to the left and move the motor and pump to the right to clear the coupling. If you have not replaced the drive coupling, now would be a good time to order and replace. With the motor out of the way, remove the three (½”) bolts holding the gearcase to the chassis and pull to remove gearcase and shaft. If you are only replacing the drive shaft seal, you do not need to open the gearcase case. Stand the gearcase so the input shaft is facing up, or what fluid is left in the gearcase will come out. One question I see a lot is how do you remove the seal. One, buy a real expensive tool that you will only use once, or take a screwdriver with about a ¼” blade, stick it between the shaft and the seal, gently leverage the seal out while going around the shaft. After the seal is removed, oil can be added thru the seal hole. Understand that different oils are designed for different applications. That said, I used 90 weight gear oil from the local auto parts store, you can add it thru the seal hole. To install the seal, lightly tape it into the seal cavity, then use a socket that is close to the diameter of the seal and gently drive it in.
If you have to replace the top case seal, it will require you to take the gearcase apart. The advantage of this is, if you have an older washer, you can clean out the contaminated oil and sludge and check for wear on the parts, and replace as needed from PartSelect. Here’s a suggestion: if you have a digital camera, take pictures, this will really help when you put things back together.
Now look at the diagram that is provide by PartSelect, remove the clutch, remove the bolts on the top cover, try to keep it level or you may have a mess on your hands. Lift the cover up over the shaft. I found the top case seal very stubborn to remove. Using a small screwdriver, get between the case and the seal and gently pry it out. Replace the seal, again, by using a socket and gently taping into place. There is also a seal at the top of the drive gear that you may want to replace to keep the oil from going up into the clutch. Now its time to clean all of the years of gunk out of the case and gears. When you are ready, fill the bottom half of the gearcase with oil, about half a quart. To seal the case, I used a ultra blue silicone gasket sealer in a tube from my local auto parts store or sealant can be purchased from PartSelect. I used it on the top half of the gearcase case. Slide the top case over the shaft and evenly tighten the bolts. Reinstall the clutch to the gearcase shaft and install into the washer. I found that the motor bearings needed to be lubed, so I used white lithium grease in an aerosol can. Reinstall motor and don’t forget to put the electrical plug back into the motor and the wires that go to the capacitor and pump h
125 of 136 people found this instruction helpful.
Was this instruction helpful to you?
Michael from Murray, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Parts Used:
80040
Agitator was not working
Step 1) Take off top cap with a flat head screw driver.

2) unscrew bolt (may need extension as it may be deep in the agitator.)

3) Take upper agitator off.

4) remove clog retainer and clogs.

5) insert new clogs and re-assemble.

total time 10 to 15 min.
61 of 72 people found this instruction helpful.
Was this instruction helpful to you?
Richard from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set
Parts Used:
WPW10072840, 80040, WP3952374, 285809
Agitator would not spin
replaced the agitator cogs, bearing and the O-Ring. I looked all over Houston for these part, but found them on PartSelect. Had them in about 3 days. The repair only took about 30 minutes.

I saved a bunch of money!!
Thanks.
42 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Chris from Morgan City, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
80040, WP3363394
worn water pump and worn aggitator cogs
leaned and propped washing machine back to get access to pump, removed hose clamps and hoses,removed retainer clips, old pump was stuborn to remove but was able to pry off motor with screwdriver. sanded rust off metal shaft,put on new pump,replaced retainer clips, replaced hoses and clamps. set washer in upright position removed aggitator cap, used 7/16' socket with long extension,unscrewed bolt, pulled off aggitator sleave, removed cog unit, replaced cogs, put sleve back on and tightened bolt. I had the machine outside so I hooked up a water hose and an extension cord, put machine on small load and tested machine . worked like new. also when i finished the test I had noticed earlier that my hose screen had a mineral build up, cleaned that by lightly scraping and used little rust inhibitor that also tackles scales. total time was about 30 minutes. Wife is happy now and I was rewarded later.
31 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Craig from Yadkinville, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
80040
Upper agitator stopped moving
First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ears were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.
30 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Charles from San Diego, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
80040, 285587
Screw agitator would free spin
Job was easy! Just remove the top cap with a screw driver. With a socket and extension, remove the bolt that holds the agitator to the transmission shaft. Pull up on the agitator and lift it off the shaft. I had to use the screw driver to pry off the center piece that held the cogs because it did not what to separate from the rest of the agitator. Removed the pieces of the old, broken cogs, cleaned up the parts and installed the new cogs with the center piece upside down. I then took some silicone lubricant and lubed the area the cogs rub on and the opening the center piece spins in on the rest of the agitator. I then removed the Thrust Spacer on the mail part of the agitator but just lifting off the old one and putting on the new one. Then, with the center piece that holds the cogs upside down I inserted it into the upper corkscrew section of the agitator so that the cogs would not fall out. While holding the two pieces together, I turned it back right-side-up and installed it back onto the other part of the agitator and then on the shaft. Re-installed the bolt and tightened with the socket. That's it! It sounds more complicated then it really was.
28 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Robin from Westwood, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
80040, 63580, 285587
the agitator arm that rotates the clothes was not moving
pull up and off the fabric dispenser, remove the nut in the middle, and pull the piece off. underneath are 4 plastic things (dogs) that will just fall out. replace them (because they have little plastic things that jut out) and wear away. maneuver the piece back in place and tighten the screw back into place.
SAME JOB BY REPAIR CO. COST ME $95.00 THE FIRST TIME. WE USE HEAVY LOADS AND THE DOGS WEAR OUT AFTER A FEW YEARS. NOW I JUST CHANGE THEM MYSELF.***DID I ADD THAT I AM A WOMAN****
24 of 699 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
33 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    32
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

Brand
Model Number
Description
Kenmore
106.82872600
Washer - Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
110.828918100
Washer - Kenmore Washing Machine Model 110.828918100 (110828918100, 110 828918100) Parts
Kenmore
110.828918110
Washer - Kenmore Washing Machine Model 110.828918110 (110828918110, 110 828918110) Parts
Kenmore
110.828918120
Washer - Kenmore Washing Machine Model 110.828918120 (110828918120, 110 828918120) Parts
Kenmore
110.828918130
Washer - Kenmore Washing Machine Model 110.828918130 (110828918130, 110 828918130) Parts
Kenmore
110.8293130
Washer - Kenmore Washing Machine Model 110.8293130 (1108293130, 110 8293130) Parts
Kenmore
110.92093320
Washer - Kenmore Washing Machine Model 110.92093320 (11092093320, 110 92093320) Parts
Kenmore
110.92093720
Washer - Kenmore Washing Machine Model 110.92093720 (11092093720, 110 92093720) Parts
Kenmore
110.92293510
Washer - Kenmore Washing Machine Model 110.92293510 (11092293510, 110 92293510) Parts
Kenmore
110.92570200
Washer - Kenmore Washing Machine Model 110.92570200 (11092570200, 110 92570200) Parts
Kenmore
110.9281100
Washer - Kenmore Washing Machine Model 110.9281100 (1109281100, 110 9281100) Parts
Kenmore
110.9975820
Washer Dryer Combo - Kenmore Washer/Dryer Combo Model 110.9975820 (1109975820, 110 9975820) Parts
Kenmore
110088732791
Washer Dryer Combo
Kenmore
11010202000
Washer
Kenmore
11010202001
Washer
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer
Kenmore
11012202100
Washer
Kenmore
11012502100
Washer
Kenmore
11012852100
Washer
Kenmore
11014502300
Washer
Kenmore
11014852300
Washer
Kenmore
11015732400
Washer
Kenmore
11015842400
Washer - Kenmore Washing Machine
Kenmore
11015852400
Washer
Kenmore
11015862400
Washer
Kenmore
11015864400
Washer
Kenmore
11015942400
Washer