Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
22 of 233 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking drain hose
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Other Parts Used:
Steve from Cypress, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
16 of 19 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
there was a hole in the original drain hose
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
Other Parts Used:
Kathy from Pittsburgh, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
10 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain hose leaking
Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.
Other Parts Used:
Maryanne from BEND, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old outgoing water hose leaking
1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.
Other Parts Used:
Mary from BIRMINGHAM, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drainage hose had a break in it.
Removed broken hose and replaced with new hose. My washer will be 21 years old in January.
Other Parts Used:
Virginia from SNELLVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
hose split
Pulled washer out from wall removed clamp and old drain hose addnew hose replaced clamp put washer back in plact connected drain to outlet simple operation
Other Parts Used:
Sam from Sharon, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rats chewed through hose.
New hose was perfect, went on easy.
Other Parts Used:
Bobb from SANTA BARBARA, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lisa
November 1, 2017
What is the diameter of this hose?
For model number RAS8333PQ0
Hi Lisa, Thank you for the question. This hose has a 1 1/8" inner diameter Hope this helps!
9 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Tom
August 2, 2017
How long is this drain hose? Thanks.
For model number LA5558XTN2
Hi Tom,
Thank you for your inquiry. This hose is approximately 48" long. I hope that helps!
8 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Raymond
October 4, 2019
My external drain hose split and obviously was leaking. I replaced it with a 6 foot long hose from the local hardware store. Since I replaced the hose the leak has stopped but the washer does not drain. Six inches of water remains after running the cycles. The replacement hose is flexible and not rigid as the original hose. It is soft and kinked from being packaged. It though the kinks would go out as water pushed through the hose, but this does not seem to be happening. Does this machine require a rigid drain hose?
For model number 110.26912691
Hello Raymond, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS334596 and is showing a ridgid hose is required. Hope this helps!
2 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Robert
October 16, 2017
What is the length of the drain hose with clamp? I'm looking for a hose that is approx 6 feet long. Is that length available?
For model number KAWE760WWH0
Hi Robert, Thank you for the question. This hose is 48 inches long. For 21 inch extension use PartSelect Number PS334609.Hope this helps!
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Stephine
December 17, 2018
Does this part fit in model no. Ca2762xyw0
For model number CA2762XYW0
Hi Stephine, thank you for your question. Yes, this is the correct part for that model number. I hope that helps. Good luck with your repair.
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Mary Lou
January 14, 2019
What is the diameter of both ends of the replacement hose? My old one is 1 1/8 inches on each end.
For model number 11082873120
Hello Mary Lou, Thank you for the question. Very sorry but we do not currently have the diameter of this hose, but I can verify it is the correct hose for the model number 11082873120 and is the same size as the original. Thank you for your inquiry, good luck with this repair!
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Maureen
April 2, 2019
My Kenmore washing machine won't drain. The water stays in the machine about halfway, i don't know what part to buy.
For model number 11081863100
Hello Maureen, thank you for your question. If the washer won't drain at all in any cycle we would recommend replacing the drain pump first. The part number is PartSelect Number: PS11741239. Please enter the part number into the site for current price and availability. Good luck with your repair!
1 personfound this helpful.
Was this helpful?
Thank you for voting!
Sandi
October 5, 2023
I need an Extension part for #285664
For model number LSR8244EQ1
Hello Sandi, thank you for reaching out to PartSelect. The drain hose extension for your model is part number PS334609. We hope this information helps!
My original hose goes inside a rubber coupling then the coupling fits over the drain outlet on the back of the washer.
Outside diameter of the hose must be 1.48 inches to be tight enough to not leak in the coupling. Is this hose at least that big? The hoses that I have been told fit are 1and 1/8 inches or smaller. I am told locally that my machine is too old to have the correct size hose available. Please give me exact measurements for this hose.
For model number 110.82891820
Hi Zane,
Thank you for your question. These would be the approximate measurements for the hose. The hose is listed under the model number you provided and it would work on your washer. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Tricia
March 30, 2023
Not long enough from back of washer to drain tube in my trailer
For model number Model: LSR8010PQ0 erial: CS3175916
Hi Tricia, thank you for reaching out. Based on our research, you may use a drain hose extension, part number PS334609, to make it long enough according to your need. We hope this solves your problem!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Hose or Tube","title":"Hose or Tube","url":"/Washer-Hoses-and-Tubes.htm"},{"position":2,"name":"285664","title":"285664","url":""}]
