Models > ZBD1870N02SS > Instructions

ZBD1870N02SS General Electric Dishwasher - Instructions

All Instructions for the ZBD1870N02SS
16 - 30 of 36
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
two wheels broke off
knocked the broken piece off and snapped the new wheels on - easy breezy.
Parts Used:
Lower Rack Wheel and Stud
  • Carol from WALSENBURG, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Roller wheels on lower dish basket were worn and broken
Removed old roller with pilers and pop in New roller really easy very happy partselect had right rollers it made it easy
Parts Used:
Lower Rack Wheel and Stud
  • Jose from HOUSTON, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
holes in dishwasher silverware basket
removed old basket, put new one in
Parts Used:
Basket Assembly Silverware
  • Deborah from Los Osos, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom door gasket replacement/door latch replacement
Need to remove door from hinges to allow to SLIDE gasket thru small lip on door.After using soap and cleaning lip on dishwasher face ,Gasket never feels to grasp lip properly.Identical gasket from old design,just difficult to install.Door latch was also easy to install,BUT LATCH WAS PURCHASED IN LOCKED POSITION.Make sure to roll tumbler in latch ,or it will never lock.
Parts Used:
Basket Assembly Silverware LATCH Assembly DOOR GASKET Assembly
  • CHUCK from CINCINNATI, OH
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken upper roller
Turn water and electric off. remove\ dishwasher

take of old roller mount and replace new part

















0
Parts Used:
Upper Rack Wheel Upper Rack Rail Cap
  • Inge from ANAHEIM, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the micro filter
Just tool out the old micro filter and put in the new filter.
Parts Used:
MICROFILTER
  • Sophie from HOLYOKE, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The basket handle was broken in transit.
I ordered the silverware basket because the original started to separate. The shipment box was damaged and sure enough the handle was broken. The handle can be removed so I replaced the new handle with the old handle, since it was the basket that really needed. Pops off very easily.
Parts Used:
Basket Assembly Silverware
  • John from ANN ARBOR, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking drain hose
Removed leaking drain hose under the dishwasher from drain pump and sink drain pipe. Fed new hose behind dw connected with new clamps to dw drain pump and sink drain pipe. Put in high loop under sink.
Parts Used:
DRAIN HOSE Assembly Clamp
  • Vivian from RAMSEY, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new silverware basket
took out the old basket and put in the new basket
Parts Used:
Basket Assembly Silverware
  • CAROL from BUFFALO, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Roller wheels wore out.
manual labor.. And a little help from Milwaukee power tools.
Parts Used:
Guide Rail Bracket Assembly
  • Michael from Gwinner, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
4 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Dispenser Cap melted on heating coil
Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks
Parts Used:
Rinse Aid Cap
  • Martha from Kingman, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lower rack wheels kept falling off on right side
Definately purchase all the wheels (8) as they are smaller than original wheels. Buy the wheel with attached stud. Pull off old wheels and pop these on!
Parts Used:
Lower Rack Wheel and Stud
  • Mary from Rocky River, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the lower rack wheels were breaking
I was able to replace the wheels with the new ones I ordered which are a better design.
Parts Used:
Lower Rack Wheel and Stud
  • Nonie H from Kitty Hawk, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Studs had become worn and needed replaced
Removed all wheels, then removed and installed new studs which were designed better than the origional and re-installed. Bottom rack now slides in and out much better.
Parts Used:
Lower Rack Wheel and Stud
  • Scott from Newark, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old rinse aid cap melted by heating element
Simply screwed in the new rinse aid cap to replace the old one
Parts Used:
Rinse Aid Cap
  • Eric from Stephens City, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ZBD1870N02SS
16 - 30 of 36