All Installation Instructions for Maytag Range YMER8775AS0

Burner went out

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Parts Used:

6" Surface Element, 1200 W

Ronald from DEFIANCE, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

circuit board failure

Board failed causing element to fail as well. De-energized range. Took back panel off to get to circuit board and heating element. using Phillip's head screwdriver, removed 4 screws and disconnected wire plugs. Installed new board and re-connected wires. Put back panel on and re-energized range. Tested and worked fine.

Parts Used:

LCC195 AMBER,EHESC,CV,MY

Todd from SIMPSONVILLE, SC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

surface element not working

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

Parts Used:

6" Surface Element, 1200 W

bruce from PORTLAND, OR
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Range Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

I snapped a bolt on the main power terminal block when connecting the pigtail.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Parts Used:

Range Main Power Terminal Block

Frank from Palm Coast, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

cleaner

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Parts Used:

Cooktop Cleaner

Mary from Duarte, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

broiler pan missing

ordered new broiler pan

Parts Used:

2 Piece Broiler Pan

RAYMOND from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

heating element

screwed it in the oven and it worked.

Parts Used:

Bake Element

Victoria from NASHVILLE, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed to replace over door gasket

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Parts Used:

Door Gasket

Genie from Conshohocken, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

oven would not heat

The instructions given on this website were more than adequate, even though the element had been updated and now has only 1 point to screw down

Parts Used:

Bake Element

francis from YORK, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light would not light

Pop old one out and new one in

Parts Used:

SOCKT-LITE

Frank from LEBANON, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven light not working

replaced light socket but did not repair problem. must have burned the motherboard.

pleased with service from your company.

Parts Used:

SOCKT-LITE

Richard from Gaylord, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used: