YKESS907SS01 KitchenAid Range - Instructions

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.

Tried reusing old door hinges after removing door to access temp sensor and broke the oven glass twice.with new hinges , new glass went in easily.