XSS25GGPBCBB General Electric Refrigerator - Instructions

Part arrived in 2 days and took about 15 seconds to install. Great!! No more broken eggs!!

Because the lever was broken, when you close the refrigerator door, the freezer door would unseal slightly causing frost to build up on the inside and outside of the door.

After removing the base grille, the repair was made by simply placing the new part in the slot where the old part was then re-attaching the spring from the part to the hook in the base of the refrigerator. Now replace the base grille with the two screws. Time: About 10 minutes. Tools: Phillips screwdriver, needle nose pliers.

First turn off the power, remove the ice tray, remove the two screws holding the ice maker to the side of the freezer, use the screw driver to gently open the electrical clip for the power cord inside the freezer, remove the complete unit from freezer, bend the old stripper from the holding pin- it is flexible- it will bend, replace the new stripper on the holding pin and bend into the slot to hold it firmly, no water will come out from the fill cup into the freezer, plug in the power cord, mount back to side of freezer, you are done.

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

I popped the switch out using the blade of a small screwdriver and noticed that it connected with two wires via a slide on connector for each one. I noted the info on the old switch to identify which wire went to which terminal. I held each wire with a pair of pliers while I pulled the wire connector off the terminal on the old switch. I connected the two wires to the correct terminals on the new swith, and popped the switch back into the door frame. Easy, easy, easy and saved the $40 service call + parts cost!

Bing , Bang, Boom.

I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I searched and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.

using a small socket wrench and star shaped driver I (1) removed the two screws that held the broken stop from the bottom of the door, and (2) replaced the new stop and screwed it back in. The most difficult part of the job was opening the door in order to access the second screw.

Suggest removing black plastic grill first to gain better access to door stop screws. The grill is attached by two phillips screws, one on either end and several metal spring clips in the middle. The door stop is held by two star shaped screws that are only visible with a mirror. Suggest using a bit attached to a small ratchet.

I received part. I then used a hair dryer to smooth out kinks. Took about 15 minutes. Pulled off old gasket and replaced with new one. Used hands only.

Super easy. Hardest part was popping the plastic covers off without breaking them. I had to use a butter knife to get under it & lift it just enough
to grab it & pull easy until it turned loose.

Using my putty knife, I slid it under the light cover prying upward to remove it. I then unplugged the the light board from the wire and unsnapped from the two prongs. Then reinstalled.

1) Use plastic spudgers to remove the front control panel by levering on the front bottom of the plastic
2) Unscrew 4 retaining screws from the internal assembly
3) Slide clear plastic ice chute from the internal assembly
4) Lift the paddle 90 degrees to remove it
5) Place the spring on the paddle lug such that the long side fits in the groove on the back
6) Press the spring back, and slide the paddle into the paddle holder at a 90 degree angle
7) Once installed the short side of the spring should press against the plastic to force the paddle to its default position
8) Slide the ice chute back into the assembly
9) Replace the 4 screws holding the assembly to the refrigerator
10) Replace the front control panel

I may have missed a step here or there, but nothing major. Be mindful of the switches, and the placement of the wires. The entire process took maybe 5 minutes. I would say the most difficult part is getting the control panel off, it kind of feels like it might break, but it's a pretty robust piece.

Unplugged the fridge, and opened the freezer. Unscrewed the light panel, small screwdriver. Removed the plastic bracket. Part was frozen and I broke one of the plastic mounts. Do not do this as I am not sure if I will have to live with my cable twist tie kludge or I can get another plastic bracket. Light board is just the PCB. You need to remove the old PCB and install the new one- remember the orientation and the fact that the plastic mount piece has specific sides you can identify by the width of the slots. This is for all the other women like me. Thanks.

It was very simple! I assessed the situation and gathered my tools for the job. I used a flat head screwdriver, pliers, and electrical tape. I used the flat head screwdriver to release the switch from its location, the pliers to take the electrical terminations apart. I taped the wires individual so that I would not loose them in the door, also not to short them out. I then unpackaged the new switch to install. Pulled the tape off one of the of the terminals while holding the wire, and attached it to the new switchs terminal post. Did the same with the other wire, then snapped the new switch back into place. Immediately had results. I opened and closed the door a few times in amazement that something so annoying such as a light in your fridge could be so easy to fix. Most of all, having a business to rely on to find the part and deliver in a timely fashion. Thank you Partselect.com, you were outstanding!!!