WTW6200SW1 Whirlpool Washer - Instructions

It is good to watch a video on how to!
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.

fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.

Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.

Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)

took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.

Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!

Thanks guys.

At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.

put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks

Replaced rods with new set of 4