WRF555SDFZ11 Whirlpool Refrigerator - Instructions

The other instructions and the video provided by Parts Direct are pretty good with instructions, but they omit two steps. First, if you have an ice maker, you will need to unplug the connector on the back side of the panel you remove at the back of the refrigerator to access the drain tube. Just unplug it and you can move the removed panel to the side without disconnecting any of the water lines. Second, the instructions say to just reconnect the "bottom end" of the new p-trap drain to the drain pan at the bottom of the refrigerator. They don't tell you there are two places to connect the new p-trap to the drain pan. The original tube/trough connected to the one at the back of the drain pan on the left (viewed from the rear of the refrigerator). At first, it looks like the new p-trap won't reach to it for the connection, but if you look closer, there is another connector to the right of the original one that the p-trap connects to properly. Replacing the drain trough with the new p-trap was actually pretty easy and would only take about a half hour. Add another half hour to give the refrigerator coils a good cleaning as they will need it now that you can reach them. The real time consumer, 3 to 4 hours, is needed to use a hair dryer to melt and clear the ice from the condenser at the back of the freezer so the water can drain. Just take your time and all the ice will eventually melt and drain out so the new p-trap will work properly.

These guys had my part mailed in lighting fast! It arrived in 2 days in a padded box in perfect shape.The price was the best on line and they saved my life one day before thansgiving!! They got my vote and respect! Great job partselect!!! walt , crete illinois

Unplug the fridge then wheel the refrigerator out to where you can get to the back - you will probably have to disconnect the ice maker water hose. Using the nut driver remove all the screws from the lower panel on the fridge. You will not have to remove the water hose connection just move the panel around a little. Look on the left side (facing the back of the fridge) you will see the capacitor held onto the compressor with a spring clip. Just pull the clip toward you and that will free the capacitor. Pull up on the capacitor and that will unplug it from the compressor. Be careful not to touch the two poles on the old capacitor. Capacitors store electricity and it could give you a jolt. I used electrical tape to insulate the poles and then threw it away. Plug in the new capacitor- re-hook the clip, reinstall the back panel, plug it in and verify that the fridge is working. Hook your water hose back up and move it back into place and you are done.

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

The old gasket kept coming off. I pryed off the old plastic insert with a kitchen knife and snapped the new one in. Without the gasket the ice wasn’t being made

Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

Just pulled out theold and squeezed in the new. I forced it and it went in.

Removed the old frame and removed the metal rod from the front of the old and slide it in to the new frame.
Then I took a piece from the old frame, measured the distance to the center of the two shelf brackets mounted inside in the rear of the refrigerator. Then I drilled two holes in the salvaged piece and mounted the piece as a support under the new frame using #8 sheet metal stews. This will prevent future breaks.

Uncurl new gaskets (set out on a table or countertop) and let them get to room temperature so they straighten out. Use hands to pull off old door gaskets. Starting at corners, use hands to push gasket into the groove on the door. Make sure gasket is properly seated all the way around the door. If some part is still wrinkled or bent, carefully use a hairdryer to heat it a bit and smooth it out.

Once I took new gaskets out of carton
and put out on patio to warm up I removed old gaskets pressed in new gaskets which made a great seal
Job was easy and took no skill

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.