WM3575CW LG Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washer dicharge water pump
-
stephen from FRANKLIN, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water failure
-
Harley from OKLAHOMA CITY, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy and drum still full of water . Will not go to next cycle.
-
Marshall from ROSEVILLE, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine stopped purging water from drum to hose
Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
Parts Used:
-
Andria from EDINA, MN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearings and bearing Gasket and large basket o ring
Removed items step by step in sequence as per video to get to baskets . Knocked out bearings and gasket seal. Replaced new parts and in reverse reassembled as per video. Very difficult without video to follow. My bearings were easy to remove but some are frozen in so will need oil ,bars or pipe to fit opening to drive out old bearings. Use camera and notes of sequence to aid in reinstall. Separate and mark fasteners as removed. Note : Was initially told by appl Insurance service person my bearings were bad because when attempting to spin a noise was heard and this not covered by plan ,but I found the motor position sensor had failed by testing it with multimeter which is a low priced part and easily accessable from back. Water hose screens partially clogged also. Canceled Appl service contract.
Parts Used:
-
Larry from SWARTZ CREEK, MI
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set, Wrench set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking hose
2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.
Parts Used:
-
David from SAINT CHARLES, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold water inlet valve was leaking where solenoid attaches to valve body.
Hardest part of the job was getting the washer away from the wall. :)
Disconnect power & water
Remove top panel, two screws at back
Remove two screws holding valve to washer body
Use pliers to loosen and pull back spring clamps on three water tubes
Remove tubes by twisting and pulling
Reverse process to install new valve.
I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.
Disconnect power & water
Remove top panel, two screws at back
Remove two screws holding valve to washer body
Use pliers to loosen and pull back spring clamps on three water tubes
Remove tubes by twisting and pulling
Reverse process to install new valve.
I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.
Parts Used:
-
Fredrick from KAYSVILLE, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was putting water in tub when it was in the spin cycle
Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.
Parts Used:
-
John from SOMERSET, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Parts Used:
-
Ryan from HIGHLAND, UT
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
A Kenmore technician said we needed this part…
…and was not able to get this part for three weeks
PartSelect had it in stock and delivered within one day of ordering.
The next technician said it did not need this part and went ahead and fixed the washer.
However, your fast service and easy return were outstanding.
Thank you very much I can recommend you highly!
PartSelect had it in stock and delivered within one day of ordering.
The next technician said it did not need this part and went ahead and fixed the washer.
However, your fast service and easy return were outstanding.
Thank you very much I can recommend you highly!
Parts Used:
-
John from LAWRENCE, KS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak in top washer hose
Super straightforward to diagnose and repair.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
Parts Used:
-
Jason from S HAMILTON, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain pump inoperable
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Parts Used:
-
Gregory from PITTSBURGH, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Parts Used:
-
Jesse from CARNEGIE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water wouldn't drain
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Parts Used:
-
lawrence from DOBBS FERRY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Did not draw the water and did not finish its cycle
Remove where the water pumps are and remove the one that was damaged easily
Parts Used:
-
saul from NEW YORK, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!