WM3431HS (ALSEEUS) LG Washer - Instructions

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

disasemble the whole mashine... split outer tank...pound out old bearings... press in new... reassemble.... look for leaks... repair man estament..$900...cost me less than 100.. took 4 hours

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Removed screws from door, not hinge, replaced handle, reinstall screws and you're done!

took lid off of washer (slides back, not pry) and had to dismantle from springs, rubber around door and pistons on bottom. also had to disconnect from electrical plugs and took out dispenser drawer and all hoses. also have to take off magnetic piece devices from off back of drum. mark everything before dismantling with a black permanent marker so you will know what went where when putting back together and what pieces were facing up,top, etc. once get everything freed up, entire tub pulls up out of the washer. get old shot bearings out of drum, but be careful not to beat on it too much so that you don't damage the shaft or "oblong" the tub, etc. ordered parts that arrived in about 2 days. to put new bearings back in, get large washers -one for front and one for back -same size as the bearings so you will have equal pressure coming from front and back, put a long bolt thru the holes in the bearings with one of the large washers on each end. put a nut on the end of the bolt and begin to tighten. this will pull the bearings together back into their positions without ruining them and gives you equal pressure all around. be careful when you get them tight, they will fit snugly back into place. put it all back together carefully, just like you took it apart. if you labeled everything, you should have no problem putting the puzzle back together. before putting the tub pieces back together, i ran a bead of silicone caulk to prevent leaks. started it back up and runs great! fixed it for total of $72 (including shipping charges), which is a lot cheaper than buying a new washing machine. it is tedious and somewhat challenging, but if you are in any way mechanical, you shouldn't have any problems.

Disconnected power. Removed washer top, upper front control panel, and front panel. Removed hoses from washer drum housing. Removed cabling and support springs and stabilizers. Removed drum housing from cabinet. Removed bolts that secure the two halves of housing. Removed rotor from drum shaft. Removed stator from housing. Supported drum housing and with hammer and punch, removed drum shaft from bearings. Replaced bearings and seal and reassembled in reverse order.

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.