WM2750W Jenn-Air - Instructions

Followed instructions. Two screws frozen. Unable to loosen. Forced to grind heads off and replace with new screws.

Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.

The basic replacement of the bad seal went fairly well. Just had to follow the other guidance and pay close attention to the correct sequence so that the door goes back together as it should be. The only real difficult part was when attempting to hold the hinge downward so that the door could be properly placed back on the hinges. After closer examination I discovered that there were two holes in each of the hinges that when they were opened all the way that the holes lined up and I cut off two nails approx 2 inches long and then once I was able to pry the two hinges all the way opened and then I used them to slip in through the two holes and they worked just fine and they held the door open, until the door could be re-installed. Once installed the nail/pins could be easily removed with some needle nose pliers.

Decided since the glass was broken I might as well replace the door seal. Getting the door off and on was the most difficult part of the process as the door hinge springs are quite strong. Remove screws on the hinge. Slide door off hinges. The hinges will close rather hard. Remove screws along the outside, then inside. Keep all the screws in some order as they are different sizes. More time to clean the door than actually installing the glass and seal. Re assemble. Trick to getting the door back on is to open the hinge spring to the broil position and place a thin screwdriver in an opening in each to keep in an open position. Slide door down to the srewdriver stop and then fully open. You can then slide the door fully onto the hinge, replace the hinge screws. Easy ,for a simple housewife.

For those with an older Jenn-Air, this range has stood up under the test of time and is still in good condition. We even called Jenn-Air for the parts and they no longer carry the oven door seal for this make. Thank you PartSelect for carrying the seal. We did call in a repair man and are glad we did as taking apart the door was quite involved. We were very blessed to locate a repair man who did Jenn-Air and are very pleased with the repair.

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.

take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.

Placed new knob directly on post. No problem

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Old (broken) knob was gone, so wife oriented new knob over selector shaft, and pushed onto shaft!! PROBLEM FIXED!!!!! No fuss, no mess - just as good as new!

Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.

removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.