Models > WM2688HWM > Instructions

WM2688HWM LG Washer - Instructions

All Instructions for the WM2688HWM
31 - 45 of 178
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leaking door predetermined
Removed top of washer
Then removed front
Then reversible basket ,during spring depressed pliers
Put new gasket on inside flange first put spring back on
Put front washer panel back on and put screws back in panel holes
Put door seal on front flange and reinstalled spring on new door seal.Put too back on and finished clean up
Parts Used:
Washer Door Boot Seal
  • joseph from PIQUA, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water was building up inside drum while machine was off.
I unplugged the washer shut off the water and disconnected the hoses. Then removed the top lid and removed old valves and installed new ones. Very easy plug and play installation.
Parts Used:
Inlet Valve Assembly Water Inlet Valve - Hot
  • jaime from Las Vegas, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not spin le code
bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour
Parts Used:
SENSOR ASSEMBLY
  • gregory from TEWKSBURY, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not draining water from tub.
Honestly youtube but pretty simple install.
Parts Used:
Washing Machine Drain Pump Drain Hose Assembly
  • Steven from KREMMLING, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not run
I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .
Parts Used:
Door Lock Assembly
  • Gary from CPE GIRARDEAU, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump went out.
Watch the video to repair and follow along
Parts Used:
Washing Machine Drain Pump
  • Greg from ENUMCLAW, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very noisy when tub was spinning , tub bearings and seal were bad.
Watched a YouTube video on how to disassemble the washer step by step, replace the bearings, and reassemble the machine. was very helpful.
Parts Used:
Washer Tub Bearing, Rear Ball Bearing Washer Gasket Rear Tub Gasket
  • Gerald from CENTRALIA, KS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Excessive vibration
I followed the video -- to take apart and reversed the steps to re-install. It was fairly straight forward and corrected the issue.
Parts Used:
Shock Absorber Kit
  • Terry G from FORT WORTH, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer not pumping out and making ominous noises
Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.
Parts Used:
Washing Machine Drain Pump
  • Ray from RIO RANCHO, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dry bearing noise
I researched the symptom, watched a repair video, ordered the parts: one rear bearing, seal, and gasket. After disassembly found inner bearing to be bad. Ordered inner bearing. Then found the spider or hub shaft corroded, and ordered spider. Finally with all the parts replaced, assembled washer and returned it to service.
Parts Used:
Washer Tub Bearing, Rear Washer Gasket Rear Tub Gasket
  • ROBERT from BETHLEHEM, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Removing the Springs and reinstalling.
I followed various tube videos. The vides were very easy to follow.
But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.
Parts Used:
Washer Door Boot Seal
  • Daniel from PORTVILLE, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy and drum still full of water . Will not go to next cycle.
Follow the LG washer video.
Parts Used:
Washing Machine Drain Pump
  • Marshall from ROSEVILLE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bellow was old and pump was making noise
Disconnected power, removed top cover, removed control panel, removed door assembly then was able to access and replace the bellow and pump.
Parts Used:
Washing Machine Drain Pump Bellow - Gray With Drain Port
  • CHRIS from BAY CITY, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
w/d repeatedly fills with water during warm or hot loads
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
Parts Used:
Water Inlet Valve - Hot
  • kevin from WASHINGTON, DC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
Parts Used:
Pump Filter
  • Sandra from Livonia, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WM2688HWM
31 - 45 of 178