WM2250CW (ABWEPUS) LG Washer - Instructions

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Watch the video to repair and follow along

Follow the LG washer video.

I followed various tube videos. The vides were very easy to follow.
But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.

Turned off hot and cold water supply. Pulled out machine and disconnected hoses, unplugged power.

Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.

Slid cover back and up. This was the only tricky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.

Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.

Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.

Replace cover. Screw all screws back to secure cover. Replace trays.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

First unplug the machine. Turn the water off to the hoses. Remove the hoses from the machine to make it easier. Remove the screws from the back of the top cover. Pry the front sides with a screwdriver and lift. Standing behind the machine on the left side you’ll see the three solenoids or inlet assembly. Remove the two screws so as to take the inlet assembly out. There are hoses attached to the assembly.

The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arrived the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 seconds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

you tube it , not to hard to install

-Unplug washer
-Turn off water supply
-Pull machine away from wall
-Remove two screws on the back holding the top panel in place
-Slide top panel toward the back and remove
-Unplug electrical conectors to the control panel, remove screws and take out panel.
-Remove lint trap plastic door cover bottom front left and screw holding plastic housing.
-Take housing out.
-Remove screw that is behind plastic panel holding front panel.
-Using spanner, release spring clamp holding gasket to the front panel.
-Remove top screws holding front panel on and take off panel.
-Remove hose clamp and hose at bottom of gasket.
-Release inner spring clamp on gasket to washer drum and take out gasket.
-Install new gasket and spring clap to drum.
-Reverse the order to reassemble.

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

YouTube is your friend for many such repairs. See this link for an overall description:

https://www.youtube.com/watch?v=WuvLuC8x4_s

I had to remove the top panel to determine exactly which valve was leaking. It turned out both hot and cold-water valves were defective.

After unit is unplugged and top is removed, it's a simple matter to remove/replace hose connections and electrical connections. It took me less than an hour to complete the task once parts were in hand.

Again, YouTube is your friend for such repairs.

Unplug and disconnect water lines. Move washer out. I used soapy water to make it easier to slide because it is stacked washer and dryer. Slid dryer onto large trash can saving my back. So easy. Make sure it is heavy duty . Removed lid. Removed old part by removing to screws in back. Disconnected 3 wires, disconnected one hose at a time while reattaching each one to new part. That way I was sure to get them back in the right place. Attached back to machine . Put water hoses back on and checked for leaks before but lid and dryer back in place. Ta da!! This was so easy. I am a 57 year old woman and this was pretty simple. I tried trouble shooting by using tub cleaner and everything as manual suggested but it still leaked. Watch a lot of you tube. Apparently lg has this happen with this part a lot. Thank you parts select. I’m sure this saved me a lot of money. I have had enough money bleeding from my pockets with bigger home problems. Thank you.

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.