WM2150HR LG Washer - Instructions

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!

Took off the old one and put the other one on. The only difficulty was that my husband has big hands and had a hard time getting to one end.

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the valve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.

Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.

remove the front part of the machine to get to the door hinge.

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequence. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.