WM2032HS LG Washer - Instructions

Honestly youtube but pretty simple install.

I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .

Google LG washing machine bearing replacement, you'll find a very informative video narrated by a British gentleman who will walk you through the steps. If you are even a slightly handy DIY'er this is an easy job although very time consuming. Take your time with reassembling the machine. I missed a couple of connections and while testing it out I flooded the laundry room. Could have been avoided if I had taken a picture of every individual item I disconnected.

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Watched a YouTube video on how to disassemble the washer step by step, replace the bearings, and reassemble the machine. was very helpful.

Watch the video to repair and follow along

Started with some resin paper on the floor, some painter’s tape, and a sharpie to keep track of screws and removed parts (painter’s tape to stick hardware to). Set up iPad on dryer and followed every step by step instruction by pausing the video. The instructions were perfect (but would have liked some more close up shots). Installation of new bearings was exactly as demonstrated and truly appreciated the step by step descriptions to put it all back. Hardest part of the repair was replacing the wire ring on the rubble gasket — only step not displayed. Suggestions for future repair videos: 1) how to organized hardware as removed; 2) more close ups; 3) a video showing the problem at the start followed by a video showing post repair. As a visual person, I have spend the past few days watching the spin cycle wondering if there is a wobble or shudder etc… Similar to the feeling of buying a used car…every clunk or shudder gets you worried. Love that I saved $1000 plus taking on the repair.

Follow the LG washer video.

I followed various tube videos. The vides were very easy to follow.
But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.

I researched the symptom, watched a repair video, ordered the parts: one rear bearing, seal, and gasket. After disassembly found inner bearing to be bad. Ordered inner bearing. Then found the spider or hub shaft corroded, and ordered spider. Finally with all the parts replaced, assembled washer and returned it to service.

Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!

Disconnected power, removed top cover, removed control panel, removed door assembly then was able to access and replace the bellow and pump.

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.