WM2016CW LG Washer - Instructions

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

I ran the spin & drain cycle to empty the drum,I waited to be see how long it took to see a noticeable level of water in the drum (1-2hrs).decided to check the cold water valve first.Found that there was rust forming around the solnoid piston,making it hang up,most of the time it tryed to open, or close. cleaned with light sand paper(piston), and ordered part with parts select. Which was real easy,because of the knowledgeable staff,parts came in as promised,and in good shape,and most important of all it was the exact replacement part. My wife is HAPPY,which makes my life good too! THANKS Parts select..

Basic skill

First, slide top cover back, then lift of washer. Remember to turn off water supply and disconnect cold water hose before working on valve. Also, unplug washer from wall socket. Disconnect three small electric plugs from valve, noting the postion on valve,then disconnect the water hoses from valve, noting postition of each hose. Remove two small screws holding valve to washer,remove and replace valve.reistall valve, reconnect hoses and electric connectors. Reconnect water supply, turn on water supply, check for leak, reconnect power cord to wall socket. Run washer through normal wash cycle, observing water valve for leaks, normal operation, if no problems, then reinstall top on washer

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

Loosened hose clamps to remove old bellows. That seemed simple but was awkward reaching into the confined space. Clamp adjustments were all installed facing away from access opening. New one went on easy and I reinstalled clamps facing the opening. Perfect fit!

Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)

The most difficult part was moving both the dryer and washer from the laundry room, into the garage. Be sure to unplug and turn off both hot and cold water, gas, and disconnect gas from the dryer before disconnecting hoses and dryer vent. I walked them out with the help of my sweet little wife. I got on utube to find a film on disassembly of the wm2277hs. This is vital because it comes apart like a chinese puzzle box. With the top panel removed, I hooked the garden hose up to the cold side and found the middle solenoid was leaking on the inlet valve. I decided to replace both hot and cold inlet valves along with the four hoses. The hoses had little cracks in them. It cost more but I expect it will save hassle down the road. After replacing the parts, I tested it all with the garden hose, then put it back in the laundry room. Final testing included looking for leaks and dish soap on the gas connection looking for a bubble. Suggest you pay for faster shipping. My stuff came in three separate shipments and took a week. It was about $85 bucks. Good luck.

greate very easy and the parts fit awsome the shiping was fast and easy very satified