WM1815CS LG Washer - Instructions

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

removed two screws from back of front load washer slid the top back two inches and pulled up removing the top.Turned the water off at the shut off . Used the pliers to remove the clamps on the hose to replace. Put the new hose on with new clamps. Un screwed the two screws holding the inlet valve and removed the hose and clamp. Put the new part in and put the hose and clamp back on then put the two screws back that hold the inlet valve.Total time to unpack the parts and install 7 minutes. All I did was google it on youtube and order the parts from this site which only took 2 days and tah dah .

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

1. Unplug washer. 2. Shut off water supply (hot and cold). 3.Remove hot water hose at washer inlet. 4. Remove the 2 plastic pieces that hold the washer top to the washer body by removing the 2 retaining screws. 5. Pull the top back to remove and set the washer top off to the side. 6. Unclip the electric harness from the inlet water valve. 7. With your pliers, loosen the clamp on the water inlet valve discharge hose and remove the hose from the valve. 8. Loosen and remove the 2 screws holding the inlet valve to the washer body. Install new hot water inlet valve and follow steps in reverse. Check for leaks before plugging washer back in. Run washer and check for leaks. Note: Excellent video available on You Tube. Consider replacing both the hot and cold water connecting hoses during the repair if they are old.

Unscrew door and insert. Replace hinge. Screwed in. Replaced insert then door. Gave it lite slam. I took longer cleaning lint and glass. I too should be a repairman.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

Disconnect electric and remove top cover and remove connectors and hoses then the valves

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.