WM1815CS LG Washer - Instructions

Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.

Took out old sensor and put in new one.

WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.

Remove where the water pumps are and remove the one that was damaged easily

Unscrewed 2 screws holding part. Removed old part & replaced with new.

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!

Hardest part of the job was getting the washer away from the wall. :)
Disconnect power & water
Remove top panel, two screws at back
Remove two screws holding valve to washer body
Use pliers to loosen and pull back spring clamps on three water tubes
Remove tubes by twisting and pulling
Reverse process to install new valve.

I am convinced that the original valve began leaking because I had heard water hammer for years as that valve opened and closed during operation. I bought two water hammer arrestors (less than $30) that attach inline with the inlet hoses and I think that will prevent the problem from recurring.

Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.

followed video exactly and it worked perfectly

You have to take the back plate off the machine.The hose is all the way up front on the bottom right hand side.It has a spring clamp on it.You have to turn the hose to reach the clamp.After that the job isn't that bad.

Straight forward repair when you have the correct part.
Remove rear panel,
Remove magnetic rotor off drum.
Remove rotor, unclip sensor, replace with new sensor.
Put back together in reverse order.

Drum spins !!!

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.