All Installation Instructions for Whirlpool Washer WFW9400SZ03

The door bellows had a cut in it

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Parts Used:

Washer Door Bellow

Arthur from MORGANTOWN, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Ripped bellowspul

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

Parts Used:

Washer Door Bellow

WILLIAM from REPUBLIC, MO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Spring balanced tub violent shake on spin

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.

Parts Used:

Shock Absorber

Paul from TARPON SPGS, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Multiple water leaks, all rubber parts are chewed up from a mouse 1/

1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.

Parts Used:

Vent Hose Exhaust

Tom from SAN MARCOS, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bellow was damaged,water leakage.

First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.

Parts Used:

Washer Door Bellow

Gopaul from Queens, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Replace Bellows between door and tub

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

Parts Used:

Washer Door Bellow

Gerald from Douglas, AL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Inlet valve was stuck in open position allowing washer to fill with water when not in use.

Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.

Parts Used:

Washer Water Inlet Flowmeter

Washer Water Inlet Valve

john from YARDLEY, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The video supplied by you was great and it worked very well.

It was fast and pretty easy to do.

Parts Used:

Washer Door Bellow

Michael from NEWBERG, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Tub filling when power was off due to inlet valve leak.

Followed instructions as shown on repair video at site.

Parts Used:

Washer Water Inlet Valve

Francisco from DELTONA, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Leaking water inlet hoses.

Removed the old hoses and screwed on the new hoses.

Parts Used:

Inlet Hose - 5 FT

Helen from NASHUA, NH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.

This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.

Parts Used:

Washer Water Inlet Valve

Dennis from AUSTIN, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken hinge

Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy

Parts Used:

Washing Machine Door Hinge

Anthony from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

Parts Used: