WFW9400STA10 Whirlpool Washer - Instructions

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.

Replaced the pump. Continued to get the F9E1 error. Removed and cleaned the drain pipe between the drum and the pump. Problem resolved.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.

This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

I followed the directions as given in a video from this site, and it was pretty simple. It can be done without power tools, although I used screw driver heads on a drill. The only iffy part was that some of the star-shaped screw heads were shallow and I had to be careful not to strip them. In brief, the fix required removing the door from the machine, unscrewing the inside of the door from the outside, removing the broken hinge, inserting the new hinge, re-aligning the inside and outside of door, screwing it back together, and re-attaching to the machine.

Had difficulty getting the door off the washer because I didn't realize there were two hooks in addition to the two screws that held the door to the washer. I reviewed the repair video several times through out the repair. Probably unscrewed more than I needed. Got the new hinge installed on the door. The problem was I couldn't hold the door at the right angle to get the hooks inserted. The washer is near the wall so I couldn't open it all the way and bending over at an odd angle didn't help. At nearly 80 I don't have the strength I used to!! After trying and with the door falling on my arm I gave up and called a friend. We did have difficulty getting the hooks inserted correctly. I held the door and she got the hooks in. On the good side, the hinge part fit like it should!!