WFW8410SW03 Whirlpool Washer - Instructions

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included

very easy to take off the bad belt and easy to put the other on. skill level would be a low anyone with a socet rench and a screw driver can replace the drive belt. shipping was extremly fast. 3-6 day shipping was there in 2 days.

Replace water pump

Just went by instructions provided by parts web site

The new drawer came and I took out the the detergent despensor piece from the old drawer and placed it in the new drawer and put the new drawer back into the washer. Now the front of the washer is complete. Good as new. Part also arrived in a timely manor too. Very pleased

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

We purchased a new pump and installed it very easily. My washer works great!

Received water valve in three days, remove top on washer, removed old part and replaced valve with new one, real easy fix, any one could do this. PartSelect confirmed this was the problem and part I needed.

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.