WFW8300SW01 Whirlpool Washer - Instructions

Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.

First, I looked at a replace bellows video on U-Tube that saved a lot of time in knowing how to proceed. You really need nutdrivers as sockets won't fit on the screws. Fitting the bellows on the large drum is not as simple as it appeared in the movie. It took several attempts to get it in place, but it was simple to place the clamp after it was there. Other than that, just follow the steps in the movie for your model

First I removed the bottom panels then the door then the top then the front control panel, I had to go to different web site to get directions on how to do this, after you remove screws you have to unplug U18 from electrical control box. Then remove bumper, find wire around front of bumper and remove using needle nose pliers, then remove back of bumper from tub using phillips head screwdriver. Then with help we replaced with bumper. and put the machine back together. My complaint is there were NO instructions in the box with the bumper and the ones on your web page are not detailed enough. I had to search the web "how to remove maytag door bumper" before I found how to remove it.

Got parts in mail. The new parts seem to be better than originals. Remove bottom front access panel to reach shocks. Revove nuts and bolts from bottom mount. Then remove any existing pieces from top mount. Twist in new shocks at top (this part was why I put the bit difficult. Sme were hard to twist.),then pull down and put bolt back in bottom mount and tighten back up. re-install front cover and clean up.

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

Took less than 5 minutes to replace, So Happy;-)

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Replace water pump

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

Just went by instructions provided by parts web site