WED6400SB0 Whirlpool Dryer - Instructions

Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.

This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Taken dry a part remove the belt and then the idle replace with new one taken about 30 minutes.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

pushed the broken catch into the door and snapped the new one back in. Works perfectly!

I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.

flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.

Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.

Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

Did not take the door off..applied adhesive and seal fit perfectly..used packaging wide tape to secure for a bit while adhesive dried..waited 24 hrs..holding well..dryer is back to working order..thank you..I received the seal in 2 days after ordering!!

Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new

Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.