WED6200SW1 Whirlpool Dryer - Instructions

Used putty knife to release catches on dryer top. Removed two screws in Lint Filter cover. Used Nut driver to remove the screws holding the front on. Removed the drum and had easy access to all the parts I was having trouble with. I believe the real problem was the Idler pulley but since I was already there I replaced the drum rollers also. While drum was out I vacuumed the inside of the cabinet. After parts were replaced i put everything back together in reverse order. Very Easy

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

very easily

Just follow the instructions the one was provided with Maitanace kit we bought from you.

*as with all electrical repairs I unplugged dryer from the outlet*

I disconnected the wires to the heating element, removed the 2 nut screws holding the heating element in place and removed the defective heating element. It looked like the heating element had darkened on the lower end and the wire terminals definitely looked like they had built some resistance that lead to the connection wire melting.

I slid the new heating element in and replaced the 2 screws. I cut the melted portion of the connection wire about 1/2" beyond the melted area and stripped the wire jacket exposing clean wire. I took the connection kit & clean wire lead, divided the wires into 2 groups on each end and braided them together and twisted them to a hand tight grouping. I then took the lead cap and twisted into onto the braided wire connection until it was also hand tight and snug.

I then reconnected the heating element connection wire back to the terminal end of the heating element and made sure all connections were snug.

I plugged the dryer back in, reset the dryer by turning the dial to a timed setting then back to off. I set the heat to low turned the dial to a time dry and turned on the dryer to ensure the element heated up and that the wired connection was secure. After 20 - 30 seconds, the element maintained heat and no issues were found with the fixed wire.

I replaced the dryer back and all screws and reconnected the vent hose. Dryer has worked great for the last few weeks with no issues. I was really surprised it was that easy to fix.

Take door off dryer (unscrew four screws). Lay door on flat surface. Using glue provided glue down new seal. Put dryer door back on and you're done!

I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.

I looked at the parts breakdown to see how it cam apart.

I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

I pulled off the front panel to access the motor and pulley systems underneath the tumbling cylinder. I disconnected the tension spring on the pulley assemble. Then after sliding the belt off the pulley, I removed the screw that held the pulley to the bracket. I put the new pulley on, slide the belt over the new pulley and attached the spring. Nothing difficult, just a little uncomfortable squeezing both hands into the bottom space.

Pliers and screw driver to pop out the old door catch and pop in the new one. Saved $69.95 service charge for a tech to come to the home.

1 screw to replace.

Followed video instructions using flat scraper & pliers (easy).Tried to remove "SPARE" latch on other side of door. Even removed door myself (Easy).Tried for (45) minutes without success. Ordered part @ 11:30 pm. Replaced door easily by myself by leaving bottom screw for each hinge in place & replaced broken latch. Received new latch in (5) days. Removed broken latch without tools & replaced new latch in (15) seconds. Need help from any "Ladies" who can remove second latch so it is available for next replacement. This "Engineer" was too lazy to remove the screws around the door because he was going to "Follow the Video". Overall it was an "Easy Fix". Keep the 'Videos"coming.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519