WDF320PADB0 Whirlpool Dishwasher - Instructions

Pulled out old gasket, pressed in new starting middle top. No more leak.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

I followed installation instructions from this site and all went well.

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.

I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.

Pulled dishwasher out unplug the wire on each side unscrew the nut on each side lift up in the back of element pull it out on metal holder for element and put the new one in really easy thanks so much for the help!!

Removed the old pump, got part number from it, ordered the part. Simply a matter of slipping the new pump into place, reconnecting the electric, testing the machine out to make sure it did not leak. Then slid back in place with the cabinets.

Had to repurchase the correct one. I was also sent a used part that I am still waiting for a call tag to send back. I was also given an email address for customer service but low and behold it also didn’t work!!!!

Followed whirlpool Youtube available for DIY.

Caution....ensure that the pump POWER plug does not loosen when reinserting the pump/drain/filter (middle of dishwasher bottom). The plug can get offset if it hits the electrical conduit or water feed/drain hoses under the dishwasher.

Minimal water when disconnecting drain hoses...have towels at the ready.

Again, follow the Youtube video!

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.

Watched video, removed the door gasket and replaced