WCVH6260F0WW General Electric Washer - Instructions

Unplug the machine. Remove the 4 screws on the back panel of the washer. Loosen the tub pulley bolt. Remove the old belt (mine did not completely break, it was shredded and slipped off the pulley). Replace with the new belt. Tighten the pulley bolt. Put the back panel on. Plug in the washer. It is working like new. :)

VERY simple, just took two philips screws off of the door, replaced the broken part, put the screws back in! LOL

All i did is pull the front panel off,then n removed the front clap with channel locks then the side clamp the same way.i then removed the main clamp with a Phillips screwdriver very simple not ever 15 minutes to do

Step 1- pull washer away from wall. Step2- unplug power, shut off water and disconnect lines, and disconnect drain line. Step 3- unscrew 3 screws from bk and 3 screws from behind control panel. Step 4- remove back of control panel and top of washer. Step 5- unplug wires from old valve and plug into new valve to avoid wrong connection take out screw from back releasing old valve , insert new valve and put back screw. Step 6 put top of washer and back of control panel on and insert screws. Step 7- reconnect hoses and drain , plug washer in and test. All done. I recommend adjusting to level if necessary at this point before pushing back against wall. Good luck. Hope this helps somebody. Jon

First I removed the excess water by using my shop-vac both inside the machine as well as near the bottom drain valve. After cleaning out that valve (which somehow had accumulated a pair of underwear) it was apparent that the drainage pump motor was no working (loud hum, not spinning). Replacement was easy, folowing instructions found everywhere on-line. Now the machine is working perfectly again.

After I disconnected the power and water and turned the washer around. I removed the back panel cover and the top and back panel to get to the pulley wheel. Once I remove the retaining nut and pulley the wheel off the spindle, i compared the new and the old parts and noticed the obvious wear on the old part, luckily the spindle was not damaged and still functional. Placing the new pulley wheel was a little more challenging. Once I seated the pulley wheel with a gentle tap from a rubber mallet. I fitted the lock nut onto the spindle and continued seating the wheel evenly using the nut to the prescribed torque pressure. After I reassembled the washer and reconnected the water and power, tested the washer, and success!

Called a Repair Man, he came installed the part and I now have a working washer once again:)

Best to watch youtube video and take the time to take washer apart and gain the access needed. I completed repair and dismantled the filter and cleaned it in about an hour, better than the average of 2 hours.

Removed top cover, loosened front door cover, removed & replaced old cracked plastic 'water inlet tube', reinstalled front door unit & top cover. Very tight space to work in when not completely removing front door unit.

Followed your instruction, very easy. I installed Camco 90" & 45" Brass elbows to relieve strain on hoses.

Removed top and front control panel. Shut off water, disconnect water lines at front and dispenser. Remove dispenser. Remove water inlet pipe by pulling out of boot. Install new pipe.Reverse proceedure. Note, these pipes may tend to split on the bottom.

I watched the video and followed the instructions. First remove power. Remove the rear cover from the control panel and the top cover. Then remove screws that secure the control panel to the frame and remove the control panel. Remove the bottom cover. Then remove the lock ring that holds the rubber boot to the front panel. Remove the door and remove the water inlet pipe. Assemble the machine and run a test cycle.

I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.

This is the second door boot seal that I've replaced on my GE Washer (I don't know the model number). I turned on my IPad, went on YouTube, and found this video: "GE Front Loader Washer Gasket Replacement." I placed the IPad on top of the dryer which was right next to the washer and followed the instructions step by step. I used the pause and play buttons repeatedly to ensure I followed the instructions correctly. The hardest part was placing two retainer rings back on. These retainer rings are used to attach the gasket to the washer drum and to the door opening. When the door is closed it effectively seals the drum preventing water from spilling out or leaking. Before reinstalling both rings, ensure that the gasket is properly seated inside the appropriate grooves on the drum and the door opening respectively. It’s a very tight fit between gasket and metal, so you have to make sure the gasket is properly seated all the way around. The inside retainer ring can be tighten with a Philips screw driver or a small wrench. Not as easy as it sounds because you don't have too much room to work with. I had to grab the drum on the right side and tilt to the left in order to get a little more room for my screwdriver. It may be easier with a small wrench, but I don't have the patience. The second retainer ring goes on the outside of the gasket and the door opening. This ring is spring loaded. Attempt to place as much of the ring inside the groove before the spring loaded tension prevents you from going any further. When you get to this point, take a flat tip screwdriver (careful not to damage the gasket) and hold the retainer ring in place while moving counterclockwise and with a second flat tip screwdriver stretched the ring and popped into place until the whole ring is in place. The guy in the video does this effortlessly with only his hands. The first time I did this, my wife helped me do it. She held the left side while I used two flat tip screwdrivers to stretch the ring, pop in place, hold, stretch, and pop in place until complete. Once you're done you will feel good about yourself and grateful to the gentleman who recorded the video and was nice enough to share. Good luck.

Sandblasted spider to thoroughly clean it and increase ductility.We used aluminum foil covered in 5200 on one side to cover holes eaten through spider. Then glued the spider to the drum and filled inside rim of spider with a nice layer of 5200. If the spider was made of stainless steel, the washer would still be running great. Thanks