VBXR1060V1WW Hotpoint Washer - Instructions

I took the plastic agitator out and checked the agitator coupling underneath. I unscrewed the agitator coupling and looked inside. It appeared that the grooves on the agitator coupling which attaches to the stem had become stripped. I ordered the $6.00 agitator coupling and screwed it back onto the stem. The plastic agitator slipped back onto the coupler and it worked perfectly after that.

pulled agitator off unscrewed bolt holding coupling on put new coupling on bolt in place put agitator on. washer working good

Slide rope beneath agitator.
Pull up with good force..agitator will separate from coupling.
Remove screw from coupling.
Slide coupling off.
Slide on new coupling.
Install screw included with the new agitator (Don't use old screw. The new one is a specialty part designed for new coupling)
Slide agitator back down over coupling.
Done

I reached under the agitator on two sides with my fingers and with one good upward yank the agitator came loose. I removed the agitator from the inside of the machine, I seen the Agitator Coupling was spinning in both directions so I felt that it may have been broken. I removed the one bolt hold the Agitator Coupling in place, I remove and inspected the Coupling and noticed that the spline was worn out. I cleaned the transmission spine that the Coupling slides over with a wire brush while using a shop vacuum to catch any loose debris. I installed new Agitator Coupling Kit slipped the Agitator back inside the machine over the coupling and pressed it down until it snapped into place. Job done. Machine works great.

Remove back of washer, remove switch, replace with new pressure switch attach elements and put back of washer back on --fixed washer

First pulled the element 4 inches then removed one screw size 7/16 wrench then put new part alligetor copling

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

it wasn't as hard as i thought it would be. just remove the
parts don to the agitator coupling press back on the steel spline after inspection and cleaning put the bolt back and the washer was back working like new.

took the old bolt and coupling off replaced with the new one and it's agitating great. I watched the video on the this website that explained how to do it and it was real easy and a cheap fix!

Replaced the Agitator Coupling. Ordering was very easy and I received the part the next day. It's good to know that there is a company that you could get parts from and receiving the part in such a short time. Thank you very much!!! :)

take out the agitator (pull straight up), remove old coupling by using a phillips head screw driver and install the new one.

Using the diagrams from the website, I was trying to determine the source of the noise. Thought I was losing the clutch, but then determined from your website that this model has no clutch. Turned out to be a couple of pieces from the agitator coupling had broken off, and were riding between the agitator and the tub. Cleaned out the plastic and the washer worked. Then ordered and replaced the coupling. Would have only taken about 15 minutes, but I dropped a screw down in the outer tub, and had to fish it out.

I lifted the agitator stragiht up. removed agitator coupling bolt w/pliers. went on Partselect.com to order replacement coupling, which supplied me with exploded diagrams, entered part number in box at the bottom of the screen and waited 2 days. It then took me less than 5 minitues to complete.

I'm happy I looked at the motor spline while it was running and found it was not slipping. Thanks to GE having a parts list in the compartment behind the controls. I found the part name and number. A quick search of the part number came up with your web site. I payed less for the parts and shipping than driving around town would have cost in gas, much less my time. Thank you

Removed the agetater removed a nut on top of the coupler> Then I removed the coupler put the new one one replaced the nut and the agetater. I receved the new part in two days. Great service I would recomend to a freind and also use parts select again. Thanks very much.