TWX233RBD3 Tappan Washer - Instructions

Unpluged the washer, raised the top of the washer and removed the front of the machine. Remove the input a drain hoses, make sure you have something to drain the hoses into. These were removed with a plain pair of pliers. Remove the plastic cover then removed the two small bolts to remove the pump itself. Replaced the old pump with the new and in the reverse replaced the two electrical conections, conected the hoses, replace the cover, front of washer and dropped the top. Then connected the power and ran a load. Works like a champ!! Also shipping was very fast. And to top it off the wife is happy and we didn't spend a lot of money to replace it with a new one. Thanks Charlie

remove old belt, install new belt

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.

My wife noticed that there was water on the floor in front of the washer. So I investigated the problem and found a leaking pump. So I purchased a new pump from Parts Select and Installed it in about twenty minutes.

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

watched the video, all instructions were perfect!

UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.

Unplug unit. Unscrew securing nut, remove agitator, install new part (ensuring splines mate properly) and secure with nut. The nut is molded into the plastic top of the agitator, therefore no tools were required. Very simple and straight forward.