Models > TFX27RRBAD > Instructions

TFX27RRBAD General Electric Refrigerator - Instructions

All Instructions for the TFX27RRBAD
61 - 75 of 87
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no water to ice maker or water dispencer
replaced circuit board and water solenoids
Parts Used:
Auger and Ice Bucket Assembly
  • craig from sweeny, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Parts Used:
Ice Dispenser Solenoid Service Kit ARMATURE KIT ARMATURE KIT
  • GENE from ASHEBORO, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
old ice maker was rusty had not been using it
order new augerand ice bucked changed face plate 4 screws now have good clean ice
Parts Used:
Auger and Ice Bucket Assembly
  • Wilbur from Brazoria, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.
I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!
Parts Used:
Ice Dispenser Bucket
  • Joe from Paducah, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bad odor and rusty ice cubes. Auger had rusted and should have been covered by GE
Removed the old ice bucket assembly and dumped the contents. Removed four screws from the face plate and reinstalled it to the new ice bucket kit. Back in business.
Parts Used:
Auger and Ice Bucket Assembly
  • David from Punta Gorda, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rust in ice
Replaced auger and front helix kit.
Parts Used:
Auger and Front Helix Kit
  • James from Corpus Christi, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Parts Used:
Ice Dispenser Solenoid Service Kit
  • Charles from Spring, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Parts Used:
Ice Dispenser Solenoid Service Kit
  • David from Joliet, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not dispence ice
remove ice bucket and replace broken augar
Parts Used:
Ice Bucket Auger Kit
  • jimmy from saluda, SC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Auger and Ice Bucket for GE side by side was rusty
followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!
Parts Used:
Auger and Ice Bucket Assembly
  • Jay from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rusty icemaker, broken light shield
1) Unscrew the old ice maker from the ice bucket and remove. 2) Add the new auger and screw back into the ice bucket. 3) Ta Da. No more rusty ice cubes! The Ice schield you merely insert the tabs into the slots in the freezer. Parts all seem to fit fine
Parts Used:
Auger and Ice Bucket Assembly Light Cover Shield
  • Judy from Aurora, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice bucket assembly broke
Ice bucket and auger came fully assembled. Just had to attach the face plate from the broken ice bucket assembly and slide it into the freezer. There were only four Phillips screws involved.
Parts Used:
Auger and Ice Bucket Assembly
  • William from Collierville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken light cover
Removed broken light cover (that was held together with tape) and replaced with new part. The most amazing thing was that I was able to locate the part for a 21 year old refrigerator
Parts Used:
Light Cover Shield
  • Benjamin from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Water resivour for drinking water developed crack
The replacement part came with a one page instruction sheet. Following those instructions I cut the two hoses on the old resivour and removed it. I then cut the hoses on the new resivour to desired length (all inside the refrigerator). Using the two couplers provided with the new resivour I hocked the two hoses together and tightened them with a wrench. It took longer to clean the refrigerator than it did to replace the part. Instruction sheet was very helpful
Parts Used:
Water Dispenser Reservoir Kit
  • VERN from KEIZER, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Bucket was broken at the back where the auger turns.
Removed the bucket assembly from the freezer. Remove the four screws holding the front cover on the bucket. They are on the backside of the front cover. Installed the old front cover on the new ice bucket with the four screws.
Parts Used:
Auger and Ice Bucket Assembly
  • Ernest from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TFX27RRBAD
61 - 75 of 87