All Installation Instructions for Estate Range TES356RD0

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Light Bulb - 40W

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

range handle fell off and screw got lost

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Parts Used:

Range Screw

Frances from palm beach gardens, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Inside Light would not work

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Parts Used:

SOCKT-LITE

Dan from Caddo Mills, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

light bulb went out in my oven

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Parts Used:

Light Bulb - 40W

Janet from Ada, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Oven not heating properly

Unplug the oven, pull it out and empty the inside of the oven. The bottom heating element just unscrews from the back of the oven with two screws. Pull it out from the back of the oven and gently pull off the electrical connections. Reattach them to the new heating element, put it back into the oven and reattach the screws. Turn the oven on and check to make sure that the new heating element is working. Put everything back in the oven and you're done!

Parts Used:

Oven Bake Element

Matthew from Greenville, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Light burned out in upper oven

Screwed in light bulb and glass protector

Parts Used:

Light Bulb - 40W

Shirley from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

replaced oven lightbulb

very easy

Parts Used:

Light Bulb - 40W

peggy ann from forest city, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

Light Bulb - 40W

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 10 people found this instruction helpful.

Was this instruction helpful to you?

door glide broken

removed the old ones.then installed the new ones.

Parts Used:

Range Rear Drawer Glide

David from Port Orange, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Parts Used:

Oven Sensor

Joanne from Negaunee, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bulb Replacement

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Parts Used:

Light Bulb - 40W

Judith from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 72 people found this instruction helpful.

Was this instruction helpful to you?

water pump went out

it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins

Parts Used: