All Installation Instructions for Tappan Range TEF351EWF

Bottom oven element non-functional

Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.

Parts Used:

Oven Bake Element

Louis from GAINESVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

bake element burnt out.

removed screws,unplugged terminal leads,installed new one,back in business.

Parts Used:

Oven Bake Element

james from WOOTON, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the burner stop working

Just followed the instructions

Parts Used:

Terminal Block Kit

Anthony J from HAMMONTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Worn Drip Bowls

Pulled out the old drip bowls and replaced with the new. A simple snap!

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

River Oaks Town Homes from DES MOINES, IA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake element burned out

This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.

Parts Used:

Oven Bake Element

Mark from LAUREL, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner not heating up.

Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.

Parts Used:

Surface Element - 8 Inch - 220V

Arlene from ERIE, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The6" surface element I use the most broke. I then decided it was time to buy original replacement drop bowls, since the ones I had been buying never it correctly.

Actually, a child of average intelligence can do this. Just pull the surface elements, take the old drip bowls, install the new ones and re-install the surface elements, including the brand new one I received.

Parts Used:

Surface Element - 6 Inch

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Vitoria from SANDY VALLEY, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heating element for a frigidaire stove top broke

Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.

Parts Used:

Surface Element - 6 Inch

Rebecca from ASHEVILLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake element (bottom of oven) burnt through and snapped in two

Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...

Parts Used:

Oven Bake Element

Amber from CARLISLE, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bad element

Remove screws pull off wires and install new parts

Parts Used:

Oven Bake Element

david from PERRY, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

broke

took out the old one, screwed in the new one. very easy.

Parts Used:

Oven Bake Element

Richard from COFFEYVILLE, KS
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner not controlable

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

Parts Used:

Infinite Burner Switch - Large Element

Royce from KEENE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven was over heating temp. of oven keep climbing

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

Parts Used: