SVE47100BC Jenn-Air Range - Instructions

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

even though these sre washable filters it's still necessary to change them after so much time

I ordered 2 replacement knobs from partselect and within minutes my stovetop was just like new.
The parts were delivered in a timely manner and the entire experience was a breeze. Hopefully that will not happen again!

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

5 min. to replace old with new. Remove 2 screws
and detatch wires. Re-attach wires and replace screws. PROBLEM -THE ELEMENT- I recieve had 2 wire legs which hold the element off oven floor, these legs were loosely to element and one came off during installation. OEM had large clamp on legs- I had to remove leg from OEM and attach to
element.( Hacksaw ,file ,vice)

1. Pressed new door strike into access panel replaced access panel.
2. Turned off power to stove at main power switch panel. Opened access panel and decoupled down draft fan discharge duct. Pulled range out of counter about 3 inches to clear instrument panel side plates. Removed knob from control switch. Removed 4 screws retaining trim at bottom of instrument panel. Removed 4 screws holding instrument panel in place. Lowered instrument panel. Rotated panel top outward to expose surface burner infinite control switches. Checked all connections to suspect control switch with voltmeter to ensure no residual voltages present. Held new switch in same position as installed switch and swapped connections one at a time. Removed two screws holding old switch in panel and removed old switch. Installed new switch in panel using the two screws removed. Re-assembled range in reverse order above and slide back into counter. Recoupled downdraft fan discharge duct and reattached access panel. Reattached conrol switch knob. Restored power to range at main power switch panel. Turned control switch to High until element was red hot. Turned control knob to Low and verified element heat was reduced normally. (Control switch failure was determined by changing stove top elements and experiencing the same high only heating and loss of heat control. A small jar was used to hold all screwa as removed.)

Replaced the control.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

switch went well
removed 4 screws and lifed front panal up and out

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

removed the old by pulling it out of track and replaced it with the new filter

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

first I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires then I took new element and plug the wires in it pushed the element back in place and replaced the two screws