All Installation Instructions for Bosch Dishwasher SHPM98W75N

E15 Error Code

Turned off power and water supply. Pulled dishwasher out. Disconnected the water inlet from the back left side. Swapped out the inlet valve. Wiped up the water in the bottom pan. Put dishwasher back and turned on water and power. Simple.

Parts Used:

Access Valve

Bryan from SUWANEE, GA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

7 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Water leak on top of door.

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

Parts Used:

SEALING

Phyllis from CLERMONT, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Filter-Micro was clogged with lime from hard water.

Replacement was fast and very simple. Was completed in less than 5 minutes.

Parts Used:

FILTER-MICRO

Peter from LEXINGTON, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

dishwasher door would not close properly, spray arm would not engage plug

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!

Parts Used:

Dishwasher Spray Arm

Brian from MADISON, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this

We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.

Parts Used:

Dishwasher Circulation Pump with Heater

HOSE CLAMP

Claire from ALPINE, AZ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

6 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Water leaking and high pitch noise mid way through operation.

Mistakenly opened covers for the drain pump. Had to put those covers back in place.
Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.

Parts Used:

Dishwasher Circulation Pump with Heater

FILTER-MICRO

Lowell from SALEM, OR
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Piece that holds the insert broke

The dishwasher has inserts that can be raised and lowered to adjust the space between the dishes.
One of the holders broke.
I took out the old one and put a new one in.

1) The hardest part was identifying the piece.
This is the insert holder near the front of the rack, to the right of the cutlery basket (as you face the dishwasher)
The drawings on the site are tiny so it is hard to figure out which is the correct piece
There are 3 different numbers for each piece.
the number on the rack assembly diagram (0647)
the PartSelect Number (PS8728043) and
the Manufacturer Part Number (00616990)
I wound up ordering a number of parts and returning the ones that I didn't need (at my expense)

2) Be sure to take pictures before you remove the old piece. Once the broke piece was removed, it was not obvious to me how it the new piece connected.

Once I had the correct piece, pulling out the old one and installing the new one took no time at all.

Parts Used:

HOLDER

Dishwasher Holder

Alan from BALTIMORE, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Pump and heater failure!

Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!

Parts Used:

Dishwasher Circulation Pump with Heater

Neil from CHESTER, WV
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench (Adjustable)

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

There was a roller missing from the lower washing rack.

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

Parts Used:

Dishrack Roller - Grey

George from STURGEON BAY, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Wheels on the bottom tray broke off

The repair was extremely simple. Just lined up and popped them on. No tools needed.

Parts Used:

Dishrack Roller - Grey

Phyllis from BAYTOWN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Over the years the filter became too clogged with embedded particles

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Parts Used:

FILTER-MICRO

Jim from EDINA, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.

Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.

Parts Used:

Access Valve

Ronald from WASHINGTON, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The old basket didn’t fit in the new lower rack

just placed the basket in the rack

Parts Used:

CUTLERY BASKET

Pat from Wichita, KS
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

plastic chrome trim on the door handle was broken.

Simply removed the four screws holding the handle in place, gently removed the handle and inserted the new part. You have to be careful and work slowly in order not to damage the front of the door while getting the snap locks unsnapped.

Once the old part was removed, simply snap in the new part and put the screws back.

Great help in locating the correct part on the phone.

Parts Used: