SHEM63W52N (01) Bosch Dishwasher - Instructions

To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.

As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.

For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.

My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.

Followed the video on your site and it was an easy install with no more leakage.

They just snap in

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.

There are 2 Torx screws (I believe they're a T15) along each side and 2 across the top (6 total) that hold the upper control assembly into the door. Remove these screws; they're different from each other, so note the locations. Using a small flat blade screwdriver, unseat the control panel from the door, slide it up and out. There is an electrical connector on the right plugged into the circuit board (no need to remove it), and a control switch on the left. The control switch is held in by a push tab, so use your small flat blade screwdriver to unlock it and slide it out of its mount. There are several plastic tabs holding the circuit board in place, use your flat blade to work the circuit board free without damaging it. Once the circuit board is clear, the button assembly can be rotated up and removed from its retainer. Simply install the new button assembly and components in reverse order. Note that there's a seal along the upper edge of the control panel that needs to be seated correctly before it's fully inserted between the doors sheet metal skins. This took me less than 15 minutes to complete.

Popped the new one right on!

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.

Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.

Replaced lower dish rack

A rat got under the dishwasher and chewed up the electric’s and the hoses. Only found out when the air light came on drain not working Lots of water underneath as well as all kinds or shoot insulation and rat droppings had to wear a mask affect him use a bunch of Clorox before I could diagnose it a real party And hard to reach corners.
I ordered four parts since I found a better deal on the main electric cable which a rat head chewed through until it had an electrocuted itself. These four parts came in three different boxes and three different deliveries over two weeks. not efficient. But handwashing is over put it all together and it works I soaked the hose in hot water so I could fit it on.

Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too