All Installation Instructions for Bosch Dishwasher SHE65T55UC

cheap plactic clips on end of rope broke on the door counter balance spring

as per youtube repair

Parts Used:

Door Spring Kit

John from OOLOGAH, OK
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken door hingespring

Followed the instructions that came with the spring repair kit

Parts Used:

Door Spring Kit

Brent from WESTON, WI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Four wheels on the lower dishwasher rack came off and got lost.

I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.

Parts Used:

Dishrack Roller - Grey

james from PARSIPPANY, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wheels on the bottom tray broke off

The repair was extremely simple. Just lined up and popped them on. No tools needed.

Parts Used:

Dishrack Roller - Grey

Phyllis from BAYTOWN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We accidentally damaged the upper spray arm

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

Parts Used:

Dishwasher Spray Arm

Sheldon from ROCKAWAY, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dishwasher door dropping

After researching YouTube, I figured out the problem was the left side of the door was dropping. Took some screws out where the dishwasher was attached to the counter and cabinets. It took a bit to pull the dishwasher out but when done, the fix was easy. Reverse the process, make sure there’s power and hoses are back.

Parts Used:

Door Spring Kit

Khanh from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

New Sray arm and wheel replacement

They just snap in

Parts Used:

Dishwasher Spray Arm

SPRAY ARM

Dishrack Roller - Grey

Charles from SANTA ROSA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leakage from the dishwasher; unknown source.

Followed the video on your site and it was an easy install with no more leakage.

Parts Used:

SEALING

Bill from Seattle, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Spray arm plug into water source became worn out and difficult to engage

The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.

Parts Used:

Dishwasher Spray Arm

David from Sequim, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One Dishwasher bottom rack wheel broke

Popped the new one right on!

Parts Used:

Dishrack Roller - Grey

Toni from GREENSBORO, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Chronic water leakage

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.

Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.

Parts Used:

SEALING

Callan from CHICAGO, IL
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The metal support frame for my old cutlery basket was rusted which required replacement.

To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.

As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.

For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.

My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.

Parts Used:

Lower Dishrack

CROCKERY BASKET

CUTLERY DRAWER

Reginald from Amarillo, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.

Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.

Parts Used:

Access Valve

Ronald from WASHINGTON, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Control board was bad

Had warranty but Lowes couldn't find anyone to repair.
Ordered new board from Parts Select and had it in a few days.
15 minutes later it was fixed.
10 screws and a couple of plugs is all it took.

Parts Used: