SF325LEKW1 Whirlpool Range - Instructions

Took off old handle. Being careful not to let door slam, and took off old retainer washers.put on new handle making sure it was aligned properly. Before tightening new screws. Make sure not to cross thread or can break handle easily. I broke original handle cleaning and cross threaded. That's why I ordered new one. Thanks for carrying the handle. My stove still looks and cooks like new.

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

Even though the old igniter still glowed, I took Part Select's advise that it may be getting weak and ordered a new one. They shipped the part out the same day, very nice, however FedEx decided for some reason to hold it for five days before moving it along. Boo! When the part got here the fix was straight forward, just a matter of unscrewing a small back panel, unplugging the part, taking the old igniter off the burner and reversing the process with the new part. Oven lit right up. Thank youfor your advise and quick service.

Unplug range from electric service.
Turn off gas supply to range.OVEN
Removed the floor panel of the oven housing.
Unscrew,and removed the heat deflector. (Caution sharp metals)
Used 3/8 socket set to unscrew the old Igniter, used same bolts to mount new Igniter.
Go to the back of the range removed the metal guard held by four Phillip screws, unplug old harness, plug new factory plug (do not alter harness)

Pull range out from the wall. Unplugged the old igniter. Took the broiler assembly out of the bottom of the oven by removing 6 philips head screws. Removed the 2 screws holding the igniter & removed. Screwed the new igniter in place , replaced broiler assembly. Got back behind range plugged in the new igniter slid range back into position & turned the oven & it works like a new one.

Easy. Slide oven away from wall. Turn gas off and unplug. Open oven door. Remove grates and lift out bottom tray to access igniter. Igniter is affixed to burner tube using (QTY=2) 1/4” bolts. Used socket wrench due to limited space for nut driver handle length. Detach igniter. Got to back of oven and remove the protective plate at the bottom. There are three phillips screws. Verify you have the correct cable for igniter by tugging on igniter in oven. Pull old igniter out. Replace old igniter with new using old bolts! Run igniter cable through back using same hole as old igniter. Plug in connector in the same fashion as prior. Before reassembly, test oven. Plug oven in and turn gas back on. Set oven to bake and set temperature. If igniter lights the gas burner tube, you’re done! Reverse process to put oven back together. Job takes 20 minutes, maximum. Saved a bundle!

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

my son simply replaced the switch, so now I have a working oven light once again

Screwed in light bulb and glass protector

very easy

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Unscrewed old handle and tried to fit new one on;