SCA2000BAA - Instructions

We used the scresdriver(flat) to remove the frame inside the door, the remove several screws retaining the inner part of the door thenremoved the broken piece. We replaced the latch with the spring With a little patience, everything went fine. I broke one of the small tab, no big deal.
thanks, you saved me a lot of money/.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.

removed micro from cabinet, took off top piece and bottom piece, took off top and side piece to get to bulb. Removed bulb, replaced. Like someone said the engineers at GE should get an award for making an easy job very difficult.

Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.

-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order

It was really easy. I am not a handy person but I followed a video and got it done quite quickly. It saved me a lot of money. The local appliance repair service charges a minimum of $75 just for the visit plus parts.

removed broken latch connected to existing spring done in less than two minutes works better than new

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

Unplug power source.
Took off plastic panel partially on inside of door with door on its hinge.
Removed latch and spring.
Reinstalled new latch new spring (new part)
Reattached plastic panel to door.
Plug in power.

Part just snapped into place and wires were reattached.

Phillips screws out of the side; torx screws out of the bottom/back and slide the cover off of the back. The light is not visible but not hard to find: on the top left side mounted on a black plastic base with 1 phillips screw & stud holds other side. You can tell what the base looks like from the new part. GE probably wants you to call them to make the $-ha. Stay clear of any capacitors (shock) or chips (short) & touch the chassis to ground or if a tech, wear a ground strap.

Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.

Easy slip in to 2 hinges

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.