SCA1001KSS01 General Electric Microwave - Instructions

Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.

The staff were terrific. Thanks so much as it had a happy ending.

Anita

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.

Replace the fuses

removed key pad then removed latch assembly and replaced it with new latch assembly.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-

as easy as it gets-

Repair was simple; only a phillips head screw driver was required to remove the access plate.

Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.

Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.

One screw out - drop panel - remove and replace bulbs!!

I used a phillips screwdiver to open the light cover protecting the halogen bulbs (2) both had burned out and needed to be replaced. A bit akward to replace, but within 5 minutes both were removed. I called your part service department to order replacements,(friendly and courteous service I might add!)was told that they would arive in about 3-5 days. 1.5 days later they were on my doorstep...They were promptly plugged into my GE underhood mounted microwave, now I am back in service! You've won me over and I will tell all my friends about you. Thanks again!

Took item from sealed box and removed protective bubble wrap. Placed tray in microwave, aligning tray with turntable sprockets. Perfect fit, perfect match! And the part arrived in three days and was very competitively priced. What more is there to stay? Will use PartSelect for other replacement parts. No brainer!

Very easy replacement. Just lift out and replace with a new one!

Buying the bulb and doing the replacement my self was the best thing I had done. The same problem happened last year and I had the American Home shield insurance at that time so I called the company and they took three weeks between ordering and replacing the light, they showed me the final bill and it was $240.00....!!! This time I bought the light through partselect, got it within 48 hours and did he replacement myself within 15 min, I followed the instructions on the video and had to do an extra step ( due to the model I have) but I was able to replace the bulb and yooohooo it was working when I reconnect the power... I am a person who never tried to fix any electrical appliance before, but after this experience I will always try to do it myself... Believe me if I can do it and felt it was easy you can do it.... Thank you Partselect.... I can't speak high enough about you

Removed tray from shipping container and installed in the microwave.