SCA1000DCC03 General Electric Microwave - Instructions

Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown

This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.

The primary door latch switch contacts were not closing properly. I broke the latch bracket while removing the switch. It is only a plastic clip that holds the switch in place. I replaced the switch and bracket. The Advantium now works in all modes.

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

ordered matching handle on internet. Pried black plastic panel off inside of door--PLASTIC TABS HOLDING PANEL BREAK OFF EASILY AND MAY KEEP PANEL PERMANENTLY LOOSE--good luck! Metal frame holding window glass pried off of front of microwave(AGAIN PLASTIC TABS HOLD IT AND CAN BREAKOFF) use small wedges to pry tabs up and off metal frame. Remove screws holding handle, screw on new handle (very firmly) and assemble in reverse order.

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.

I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out