SC519J Amana Refrigerator - Instructions

The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.

Frankly, it wasn't that hard for me because I had my son-in-law do it!

First, remove the plastic cover off the top hinge by removing the single phillips head screw.

Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.

Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.

Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.

Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.

If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)

Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

removed top hinge, lifted door off bottom hinge, replaced cam, installed door.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.

Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Great service. Unpluged old switch and pluged in new one. Works great

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.